ANTI-LOCK BRAKE SYSTEM > TEST MODE PROCEDURE |
| CHECK SENSOR SIGNAL BY TEST MODE (When Using Intelligent Tester) |
Procedures for test mode:
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
A/T or CVT:
Check that the shift lever is in P and apply the parking brake.
M/T:
Check that the shift lever is in neutral and apply the parking brake.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
![]() |
Set the intelligent tester to Test Mode (select "Signal Check").
![]() |
Check that the ABS warning light blinks as shown in the illustration.
| Section Title | See procedure |
| ABS Warning Light does not Come ON |
Click here
|
| TS and CG Terminal Circuit |
Click here
|
Start the engine.
![]() |
Check the deceleration sensor.
Check that the ABS warning light is blinking as shown in the illustration.
Keep the vehicle stationary on a level surface for 1 second or more.
![]() |
Check the speed sensor.
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.

End of the sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
Read the DTCs of the signal check function.
Read the DTC(s) by following the instructions on the tester screen.
| CHECK SENSOR SIGNAL BY TEST MODE (When not Using Intelligent Tester) |
Procedures for test mode:
Turn the ignition switch off.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Check that the steering wheel is in the straight-ahead position.
A/T or CVT:
Check that the shift lever is in P and apply the parking brake.
M/T:
Check that the shift lever is in neutral and apply the parking brake.
Turn the ignition switch to ON.
![]() |
Check that the ABS warning light blinks as shown in the illustration.
| Section Title | See procedure |
| ABS Warning Light does not Come ON |
Click here
|
| TS and CG Terminal Circuit |
Click here
|
Start the engine.
![]() |
Check the deceleration sensor.
Check that the ABS warning light is blinking as shown in the illustration.
Keep the vehicle stationary on a level surface for 1 second or more.
![]() |
Check the speed sensor.
Check that the ABS warning light blinks as shown in the illustration.
Check the speed sensor signal.

End of the sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
![]() |
Read the DTCs of the signal check function.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
w/o Multi-information display:
Count the number of blinks of the ABS warning light.
w/ Multi-information display:
Count the number of blinks of the ABS warning light, and read the "[ABS]" indication on the multi-information display.

After the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
| DTC OF TEST MODE FUNCTION (SIGNAL CHECK) |
| Code No. | Diagnosis | Trouble Areas |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH |
|
| C1276/76 | Abnormal change in output signal of front speed sensor LH |
|
| C1277/77 | Abnormal change in output signal of rear speed sensor RH |
|
| C1278/78 | Abnormal change in output signal of rear speed sensor LH |
|
| C1279/79 | Acceleration sensor output voltage malfunction | Deceleration sensor |
![]() |