DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0112 | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| P0113 | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| Result | Proceed to |
| Temperature displayed is -40°C (-40°F) | A |
| Temperature displayed is 140°C (284°F) or higher | B |
| Temperature displayed same as actual intake air temperature | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Confirm a good connection at the mass air flow meter.
Disconnect the mass air flow meter connector.
Connect terminals THA and ETHA of the MAF meter wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| *1 | Mass Air Flow Meter |
| *2 | ECM |
| *3 | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (THA) - B32-87 (THA) | Always | Below 1 Ω |
| B1-2 (E2) - B32-88 (ETHA) | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| *1 | Mass Air Flow Meter |
| *2 | ECM |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (THA) or B32-87 (THA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||