DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | The Oxygen Storage Capacity (OSC) value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|

| *1 | Exhaust Manifold Converter Sub-assembly | *2 | TWC: Front Catalyst |
| *3 | Air Fuel Ratio Sensor | *4 | Heated Oxygen Sensor |
| *5 | Front Exhaust Pipe Assembly | *6 | Center Exhaust Pipe Assembly |
| *7 | TWC: Rear Catalyst | *8 | Tailpipe Assembly |



| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio sensor) | +12% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio sensor) | -12% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen sensor) | +12% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen sensor) | -12% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | A/F Condition and A/F and HO2 Sensor Condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leakage.
|
| ||||
| OK | |
| 4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) |
Replace the exhaust manifold converter sub-assembly.
| NEXT | |
| 5.REPLACE CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) |
Replace the center exhaust pipe assembly (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at a speed between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs (Pending DTCs).
| NEXT | ||
| ||
| 7.INSPECT FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leakage.
|
| ||||
| OK | ||
| ||