DTC P0100 Mass or Volume Air Flow Circuit |
DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0100 | MAF meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds (1 trip detection logic) |
|
| P0102 | MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic) |
|
| P0103 | MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic) |
|
| Mass Air Flow Rate (gm/s) | Malfunction |
| Approximately 0.0 |
|
| 271.0 or more |
|

| 1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.
Read the values displayed on the tester.
| Mass Air Flow Rate (gm/s) | Proceed to |
| 0.0 | A |
| 271.0 or more | B |
| Between 1.0 and 270.0 (*1) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK MASS AIR FLOW METER (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the Mass Air Flow (MAF) meter connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B1-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the MAF meter connector.
|
| ||||
| OK | |
| 3.INSPECT MASS AIR FLOW METER |
![]() |
Perform On-vehicle Inspection (Click here).
Inspect the function of the mass air flow meter.
Remove the mass air flow meter with the connector connected.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Blow air to the mass air flow meter and check that the intake air amount reading changes.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the MAF meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) - B32-118 (VG) | Always | Below 1 Ω |
| B1-4 (E2G) - B32-116 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) or B32-118 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY) |
Disconnect the MAF meter connector.
Remove the integration relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) - 1A-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND) |
Disconnect the MAF meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (E2G) - Body ground | Always | Below 1 Ω |
Reconnect the MAF meter connector.
|
| ||||
| NG | |
| 7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the MAF meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) - B32-118 (VG) | Always | Below 1 Ω |
| B1-4 (E2G) - B32-116 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) or B32-118 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||