AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Item | Measurement Item/ Range (Display) | Normal Condition | Diagnostic Note |
| SPD (NC) | Counter gear speed/ Min.: 0 rpm Max.: 12,750 rpm | 4th (O/D) when shift lever is on D (after warming up the engine); Intermediate shaft speed (NC) becomes close to the engine speed | Data is displayed in increments of 50 rpm |
| SPD (NT) | Input turbine speed/ Min.: 0 rpm Max.: 12,750 rpm |
| Data is displayed in increments of 50 rpm |
| Neutral Position Switch Signal | PNP switch status/ ON or OFF | Shift lever is: On P or N: ON Not on P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Shift status | ECM gear shift command/ 1st, 2nd, 3rd or 4th | Shift lever position is:
| - |
| Shift switch status (R range) | PNP switch status/ ON or OFF | Shift lever is: On R: ON Not on R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (P range) | PNP switch status/ ON or OFF | Shift lever is: On P: ON Not on P: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (N range) | PNP switch status/ ON or OFF | Shift lever is: On N: ON Not on N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (D range) | PNP switch status/ ON or OFF | Shift lever is: On D: ON Not on D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (3 range) | PNP switch status/ ON or OFF | Shift lever is: On 3: ON Not on 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (2 range) | PNP switch status/ ON or OFF | Shift lever is: On 2: ON Not on 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift switch status (L range) | PNP switch status/ ON or OFF | Shift lever is: On L: ON Not on L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 1 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or "150°C (302°F) or more", ATF temperature sensor circuit is open or short circuited |
| Lock up solenoid status | Lock-up solenoid status/ ON or OFF |
| - |
| SLT solenoid status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Item | Test Details | Diagnostic Note |
| Control the shift position | [Test Details] Operate shift solenoid valve and set each shift lever position by yourself [Vehicle Condition]
| Possible to check operation of shift solenoid valves |
| Activate the solenoid (S4) | [Test Details] Operate the shift solenoid S4 [Vehicle Condition]
| - |
| Activate the solenoid (SL1) | [Test Details] Operate the shift solenoid SL1 [Vehicle Condition]
| - |
| Activate the solenoid (SL2) | [Test Details] Operate the shift solenoid SL2 [Vehicle Condition]
| - |
| Activate the Lock Up | [Test Details] Control shift solenoid DSL to set automatic transaxle to the lock-up condition [Vehicle Condition]
| Possible to check shift solenoid valve DSL operation |
| Activate the solenoid (DSL) | [Test Details] Operate the shift solenoid DSL [Vehicle Condition]
| - |
| Activate the solenoid (SLT)* | [Test Details] Operate shift solenoid SLT and raise line pressure [Vehicle Condition]
| - |