DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 |
|
|
| P0137 |
|
|
| P0138 |
|
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio sensor) | +12% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio sensor) | -12% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen sensor) | +12% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen sensor) | -12% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor Output Voltage | Heated Oxygen Sensor Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P0138 is output | A |
| DTC P0137 is output | B |
| DTC P0136 is output | C |
| P0136, P0137 or P0138 and other DTCs are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Result | Proceed to |
| Higher than 1.0 V | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| *a | Component without harness connected (heated oxygen sensor) |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-47 (HT1B) - B32-64 (OX1B) | Always | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Alternates between higher than and below 3.3 V | OK |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Remains at higher than 3.3 V | NG |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Remains at below 3.3 V | NG |

|
| ||||
| OK | |
| 6.CHECK AIR FUEL RATIO SENSOR |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.
Clear DTCs.
Drive the vehicle according to the driving pattern listed below:
Warm up the engine.
Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle to 60 km/h (40 mph) or more and then decelerate for 5 seconds or more. Repeat this process at least 3 times.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Current B1S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.
| Result | Proceed to |
| Outside standard range | A |
| Within standard range | B |
|
| ||||
|
| ||||
| 7.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Start the engine.
Enter the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the tester, and monitor the voltage output of the heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| O2S B1S1 (Heated oxygen sensor) | Alternates between 0.5 V or more and less than 0.4 V | OK |
| Remains at 0.5 V or more | NG | |
| Remains at less than 0.4 V | NG |
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Alternates between higher than and below 3.3 V | OK |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Remains at higher than 3.3 V | NG |
| AFS Voltage B1S1 (Air fuel ratio sensor) | Remains at below 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 9.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor .
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B19-1 (HT1B) - B32-47 (HT1B) | Always | Below 1 Ω |
| B19-3 (OX1B) - B32-64 (OX1B) | Always | Below 1 Ω |
| B19-4 (E2) - B32-87 (EX1B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B19-1 (HT1B) or B32-47 (HT1B) - Body ground | Always | 10 kΩ or higher |
| B19-3 (OX1B) or B32-64 (OX1B) - Body ground | Always | 10 kΩ or higher |
| B19-4 (E2) or B32-87 (EX1B) - Body ground | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
Reconnect the ECM connector.

|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 and P0138.
Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using second gear to decelerate the vehicle.
| Result | Proceed to |
| NORMAL (No DTC output) | A |
| ABNORMAL (DTC P0136, P0137 or P0138 output) | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 and P0138.
Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using the second gear to decelerate the vehicle.
| Result | Proceed to |
| NORMAL (No DTC output) | A |
| ABNORMAL (DTC P0136, P0137 or P0138 output) | B |
|
| ||||
| A | ||
| ||