DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 P0345 |
|
|
| P0342 P0347 | Output voltage of VVT sensor is 0.3 V or less for 5 seconds (1 trip detection logic) |
|
| P0343 P0348 | Output voltage of VVT sensor is 4.7 V or more for 5 seconds (1 trip detection logic) |
|
![]() |
| Item | Content |
| Terminal | NE+ - NE- VV1+ - VV1- VV2+ - VV2- |
| Equipment Setting | 5 V/DIV. 20 ms./DIV. |
| Condition | Cranking or idling |
| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the intake camshaft VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC (3) - Body ground | 4.5 to 5.0 V |
Reconnect the VVT sensor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM) |
Disconnect the intake camshaft VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VVR+ (B93-1) - VV1+ (B96-69) | Below 1 Ω |
| VVR- (B93-2) - VV1- (B96-92) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VVL+ (B79-1) - VV2+ (B96-67) | Below 1 Ω |
| VVL- (B79-2) - VV2- (B96-90) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VVR+ (B93-1) or VV1+ (B96-69) - Body ground | 10 kΩ or higher |
| VVR- (B93-2) or VV1- (B96-92) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VVL+ (B79-1) or VV2+ (B96-67) - Body ground | 10 kΩ or higher |
| VVL- (B79-2) or VV2- (B96-90) - Body ground | 10 kΩ or higher |
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK VVT SENSOR FOR INTAKE CAMSHAFT (SENSOR INSTALLATION) |
![]() |
Check the VVT sensor installation condition.
|
| ||||
| OK | |
| 4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE) |
Check the teeth of the signal plate.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR |
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 | B |
|
| ||||
| A | ||
| ||