DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) |
DTC P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 P0051 | Air-Fuel Ratio (A/F) sensor heater (bank 1 sensor 1) current is less than 0.8 A (1 trip detection logic) |
|
| P0032 P0052 | Air-Fuel Ratio (A/F) sensor heater (bank 2 sensor 1) current is more than 10 A (1 trip detection logic) |
|
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | Always | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() |
Disconnect the A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (2) - Body ground | 9 to 14 V |
|
| ||||
| NG | |
| 3.INSPECT INTEGRATION RELAY (A/F RELAY) |
![]() |
Remove the integration relay from the engine room No. 1 relay block.
Inspect the A/F relay.
Measure the A/F relay resistance.
| Tester Connection | Specified Condition |
| 1C-1 - 1B-8 | 10 kΩ or higher |
| 1C-1 - 1B-8 | Below 1 Ω (Apply battery voltage between terminals 1B-6 and 1B-7) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY) |
![]() |
Disconnect the A/F sensor connector.
Remove the integration relay from the engine room No. 1 relay block.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (2) - 1B-8 | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (2) or 1B-8 - Body ground | 10 kΩ or higher |
Reinstall the integration relay.
Reconnect the A/F sensor connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT FUSE (A/F) |
![]() |
Remove the A/F fuse from the integration relay.
Measure the fuse resistance.
Reinstall the A/F fuse.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B96-86) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B96-93) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B96-116) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA2A (B67-1) - HA2A (B96-109) | Below 1 Ω |
| A2A+ (B67-3) - A2A+ (B96-120) | Below 1 Ω |
| A2A- (B67-4) - A2A- (B96-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B96-86) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B96-93) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B96-116) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (B67-1) or HA2A (B96-109) - Body ground | 10 kΩ or higher |
| A2A+ (B67-3) or A2A+ (B96-120) - Body ground | 10 kΩ or higher |
| A2A- (B67-4) or A2A- (B96-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connectors.
|
| ||||
| OK | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position
Turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0031, P0032, P0051 and/or P0052 | B |
|
| ||||
| A | ||
| ||