DTC C0200/31 Right Front Wheel Speed Sensor Signal |
DTC C0205/32 Left Front Wheel Speed Sensor Signal |
DTC C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH |
DTC C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH |
DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |

| DTC No. | DTC Detection Condition | Trouble Area |
| C0200/31 C0205/32 | When one of following conditions is met:
|
|
| C1235/35 C1236/36 | When either of following is detected:
|
|
| C1271/71 C1272/72 | Detected only during test mode. |
|
| C1275/75 C1276/76 | Detected only during test mode. |
|

| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Notes |
| FR Speed Open | Front speed sensor RH open detection/ ERROR or NORMAL | NORMAL | - |
| FL Speed Open | Front speed sensor LH open detection/ ERROR or NORMAL | NORMAL | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Check the Data List for proper functioning of the front speed sensor.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Notes |
| FR Wheel Speed | Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on speedometer |
| FL Wheel Speed | Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on speedometer |
|
| ||||
| OK | |
| 3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Perform a test mode inspection and check for DTCs (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT FRONT SPEED SENSOR (INSTALLATION) |
![]() |
Check that the speed sensor installation bolt is tightened properly.
|
| ||||
| OK | |
| 6.CHECK SPEED SENSOR (TIP) |
Remove the front speed sensor.
Check the sensor tip.
|
| ||||
| OK | |
| 7.CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Disconnect the A27 ECU connector.
Disconnect the A61 and A62 sensor connectors.
Measure the resistance of the wire harness side connectors.

| Tester Connection | Specified Condition |
| A27-9 (FL+) - A61-1 | Below 1 Ω |
| A27-8 (FL-) - A61-2 | Below 1 Ω |
| A27-9 (FL+) - Body ground | 10 kΩ or higher |
| A27-8 (FL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| A27-31 (FR+) - A62-1 | Below 1 Ω |
| A27-30 (FR-) - A62-2 | Below 1 Ω |
| A27-31 (FR+) - Body ground | 10 kΩ or higher |
| A27-30 (FR-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK SKID CONTROL ECU (SENSOR INPUT VOLTAGE) |
Disconnect the A61 and A62 sensor connectors.
![]() |
Measure the voltage of the wire harness side connectors.
| Tester Connection | Switch Condition | Specified Condition |
| A61-1 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| A62-1 - Body ground | Ignition switch ON | 8 to 14 V |
|
| ||||
| OK | |
| 9.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 10.REPLACE FRONT SPEED SENSOR |
Replace the front speed sensor.
| NEXT | |
| 11.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||