ENTRY AND START SYSTEM > Power Source Mode does not Change |


| 1.CHECK WHETHER DTC OUTPUT OCCURS |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester on.
Enter the following menus: Body / Main Body / DTC.
Clear the DTCs.
Check for DTCs again.
|
| ||||
| OK | |
| 2.CHECK ENTRY AND START SYSTEM |
![]() |
Remove the battery of the electrical key transmitter (Click here).
With the brake pedal (except M/T) or clutch pedal (for M/T) depressed, touch the TOYOTA mark of the key to the engine switch.
When operating the engine switch, check whether the engine switch changes to on (ACC) or on (IG).
| Result | Proceed to |
| Does not change to on (ACC) or on (IG) | A |
| Changes to on (ACC) and on (IG) | B |
|
| ||||
| A | |
| 3.INSPECT FUSE (AM2-2) |
Remove the AM2-2 fuse from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AM2-2 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (RELAY MONITOR) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| IG1 Relay Monitor(Inside) | IG1 inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Monitor(Inside) | IG2 inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| ACC Relay Monitor | ACC relay monitor/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
|
| ||||
| OK | ||
| ||
| 5.INSPECT IG1 RELAY |
![]() |
Inspect the IG1 relay.
Remove the IG1 relay from the instrument panel junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT IG2 RELAY |
![]() |
Inspect the IG2 relay.
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT ACC RELAY |
![]() |
Inspect the ACC relay.
Remove the ACC relay from the No. 5 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU) |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the E19 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay block IG2 relay terminal 1 - E19-5 (IG2D) | Always | Below 1 Ω |
| Relay block IG2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| Relay block IG2 relay terminal 1 or E19-5 (IG2D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ACC RELAY - MAIN BODY ECU) |
![]() |
Remove the ACC relay from the No. 5 relay block.
Disconnect the E18 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay block ACC relay terminal 1 - E18-4 (ACCD) | Always | Below 1 Ω |
| Relay block ACC relay terminal 2 - Body ground | Always | Below 1 Ω |
| Relay block ACC relay terminal 1 or E18-4 (ACCD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT ENGINE SWITCH |
![]() |
Remove the engine switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 7 (SS1) - 5 (GND) | Pushed | Below 1 Ω |
| 2 (SS2) - 5 (GND) | Pushed | Below 1 Ω |
| 7 (SS1) - 5 (GND) | Not pushed | 10 kΩ or higher |
| 2 (SS2) - 5 (GND) | Not pushed | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) |
![]() |
Disconnect the E18 and E19 main body ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E19-1 (AM1) - Body ground | Always | 11 to 14 V |
| E18-6 (AM2) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| E19-4 (GND2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||