DTC B1653/35 Seat Position Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1653/35 | When one of following conditions is met:
|
|

| 1.CHECK FOR DTC |
![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.
|
| ||||
| OK | |
| 3.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor and the seat position sensor.
Using a service wire, connect K1-14 (DSP+) and K1-13 (DSP-)*1 or L18-14 (DSP+) and L18-13 (DSP-)*2 of connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| 2 (LSP+) - 1 (LSP-) | Below 1 Ω |
| Tester Connection | Specified Condition |
| 2 (RSP+) - 1 (RSP-) | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| 2 (LSP+) - 1 (LSP-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| 2 (RSP+) - 1 (RSP-) | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| 2 (LSP+) - Body ground | Below 1 V |
| 1 (LSP-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| 2 (RSP+) - Body ground | Below 1 V |
| 1 (RSP-) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| 2 (LSP+) - Body ground | 1 MΩ or higher |
| 1 (LSP-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| 2 (RSP+) - Body ground | 1 MΩ or higher |
| 1 (RSP-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK SEAT POSITION SENSOR |
![]() |
Connect the connectors to the center airbag sensor and the seat position sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE SEAT POSITION SENSOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the seat position sensor (Click here).
| NEXT | |
| 9.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 10.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the front seat inner belt connector from the floor wire.
Using a service wire, connect K1-14 (DSP+) and K1-13 (DSP-)*1 or L18-14 (DSP+) and L18-13 (DSP-)*2 of connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-2 (LSP+) - K3-1 (LSP-) | Below 1 Ω |
| Tester Connection | Specified Condition |
| L16-2 (RSP+) - L16-1 (RSP-) | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 11.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the front seat inner belt connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| J10-2 (LSP+) - J10-1 (LSP-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L16-2 (RSP+) - L16-1 (RSP-) | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 12.CHECK FLOOR WIRE (TO B+) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
![]() |
Disconnect the front seat inner belt connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-2 (LSP+) - Body ground | Below 1 V |
| K3-1 (LSP-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| L16-2 (RSP+) - Body ground | Below 1 V |
| L16-1 (RSP-) - Body ground | Below 1 V |
|
| ||||
| OK | ||
| ||
| 13.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Disconnect the front seat inner belt connector from the floor wire.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-2 (LSP+) - Body ground | 1 MΩ or higher |
| K3-1 (LSP-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L16-2 (RSP+) - Body ground | 1 MΩ or higher |
| L16-1 (RSP-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||