Home › BODY › INTERIOR › FUEL LID LOCK CONTROL (for RHD)

FUEL LID LOCK CONTROL (for RHD) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    Remove the front seat assembly (Click here).

  1. for Power Seat:
    Remove the front seat assembly (Click here).



3. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



4. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. Remove the rear No. 1 seat (Click here).



5. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
  1. Remove the rear No. 1 seat (Click here).



6. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH


    B208598E01
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.



7. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH


    B208599E01
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.



8. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B216882
  1. Using a screwdriver, detach the 2 clips and 4 claws, and then remove the upper console panel.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B208601
  1. Using a screwdriver, detach the 2 clips and 4 claws, and then remove the floor shift position indicator housing.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector.



10. REMOVE SWITCH BASE


    B209104
  1. Detach the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the switch base.



11. REMOVE CONSOLE CUP HOLDER BOX


    B129881
  1. Remove the 2 screws.

  1. Detach the 2 clips and remove the cup holder box.



12. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY


    B208374
  1. Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the upper rear console panel.



13. REMOVE CONSOLE REAR END PANEL


    B129879
  1. Using a screwdriver, detach the 6 claws and remove the console rear end panel.

    HINT:
    Tape the screwdriver tip before use.



14. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH


B129877
  1. Detach the 2 claws and remove the instrument panel bracket cover.



15. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH


B129876
  1. Detach the 2 claws and remove the instrument panel bracket cover.



16. REMOVE CONSOLE BOX CARPET


    B208602
  1. Remove the console box carpet.



17. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY


    B208604
  1. Remove the 2 bolts and detach the wire harness clamp.



    B208603
  1. Remove the 2 screws.

  1. Disconnect the connector and remove the rear console box.



18. REMOVE FRONT DOOR SCUFF PLATE LH
  1. for Short Body:
    Remove the front door scuff plate .

  1. for Long Body:
    Remove the front door scuff plate .



19. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



20. REMOVE COWL SIDE TRIM BOARD LH
  1. for Short Body:
    Remove the cowl side trim board .

  1. for Long Body:
    Remove the cowl side trim board .



21. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip.



23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the rear door opening trim weatherstrip.



24. REMOVE REAR DOOR SCUFF PLATE LH
  1. for Short Body:
    Remove the rear door scuff plate .

  1. for Long Body:
    Remove the rear door scuff plate .



25. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip.



27. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the rear door opening trim weatherstrip.



28. REMOVE LOWER CENTER PILLAR GARNISH LH
  1. for Short Body:
    Remove the lower center pillar garnish .

  1. for Long Body:
    Remove the lower center pillar garnish .



29. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



30. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY
  1. Remove the package tray trim pocket.



31. REMOVE TONNEAU COVER ASSEMBLY
  1. Remove the tonneau cover.



32. REMOVE REAR FLOOR NO. 1 BOARD
  1. Remove the rear floor No. 1 board.



33. REMOVE DECK BOARD ASSEMBLY
  1. Remove the rear floor No. 1 board.



34. REMOVE REAR FLOOR NO. 3 BOARD
  1. Remove the rear floor No. 3 board.



35. REMOVE REAR FLOOR NO. 2 BOARD
  1. Remove the rear floor No. 2 board.



36. REMOVE JACK CARRIER ASSEMBLY (for Short Body)


B129715
  1. Using a clip remover, remove the 7 clips and remove the jack carrier.



37. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE
  1. for Short Body:
    Remove the rear floor No. 1 mat support side plate .

  1. for Long Body:
    Remove the rear floor No. 1 mat support side plate .



38. REMOVE BACK DOOR WEATHERSTRIP
  1. Remove the back door weatherstrip.



39. REMOVE REAR FLOOR FINISH PLATE
  1. for Short Body:
    Remove the rear floor finish plate .

  1. for Long Body:
    Remove the rear floor finish plate .



40. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH


    B132537
  1. Using a screwdriver, detach the 6 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.



41. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH


    B135482
  1. Using a screwdriver, detach the 6 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.



42. REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY (for Long Body)


    B135674
  1. Remove the bolt and tether anchor bracket.



43. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


B131613
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



44. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET


    B130163
  1. Remove the bolt, 2 washers, collar and bracket.



45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. for Short Body:
    Remove the deck trim side panel .

  1. for Long Body:
    Remove the deck trim side panel .



46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
  1. for Short Body:
    Remove the deck trim side panel .

  1. for Long Body:
    Remove the deck trim side panel .



47. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Partially remove the floor carpet.

    HINT:
    It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.



48. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
  1. Remove the bolt and fuel lid lock open lever.



  1. Remove the tape and cable from the clamps as shown in the illustration.


    B131385E01



    B131388
  1. Turn the lock retainer counterclockwise and remove the cable from the retainer.



49. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


B131389
  1. Turn the lock retainer clockwise and remove the lock retainer as shown in the illustration.