SFI SYSTEM > Fuel Pump Control Circuit |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP/SPD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.
|
| ||||
| NG | |
| 2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY INPUT VOLTAGE) |
![]() |
Measure the voltage between the terminal of the instrument panel junction block and the body ground when the ignition switch is turned ON and OFF.
| Tester Connection | Ignition Switch Condition | Specified Condition |
| IB-11 - Body ground | OFF | Below 1 V |
| IF-4 - Body ground | ||
| IB-11 - Body ground | ON | 9 to 14 V |
| IF-4 - Body ground |
|
| ||||
| NG | |
| 3.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - INTEGRATION RELAY AND IG2 RELAY) |
![]() |
Remove the integration relay and IG2 relay from the engine room No. 1 relay block.
Disconnect the instrument panel junction block connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| IG2 relay 5 - IF-4 | Below 1 Ω |
| 1A-4 - IB-11 | Below 1 Ω |
| IF-4 - Body ground | 10 kΩor higher |
| IB-11 - Body ground | 10 kΩor higher |
Reinstall the integration relay and IG2 relay.
Reconnect the instrument panel junction block connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY) |
![]() |
Remove the instrument panel junction block.
Measure the C/OPN relay resistance.
| Tester Connection | Specified Condition |
| IB-11 - IA-8 | 10 kΩ or higher |
| Below 1 Ω (When battery voltage is applied to terminals IF-4 and IE-5) |
Reinstall the instrument panel junction block.
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - ECM) |
![]() |
Disconnect the ECM connector.
Disconnect the IE connector from the instrument panel junction block.
Measure the resistance.
| Tester Connection | Specified Condition |
| IE-5 - A12-7 (FC) | Below 1Ω |
| IE-5 or A12-7 (FC) - Body ground | 10 kΩ or higher |
Reconnect the instrument panel junction block and the ECM connectors.
|
| ||||
| OK | |
| 6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check the operation of the relay while operating it using the intelligent tester.
|
| ||||
| NG | |
| 7.INSPECT F/PMP RELAY |
Inspect the F/PMP relay (Click here).
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (F/PMP RELAY - ECM AND INSTRUMENT PANEL JUNCTION BLOCK) |
![]() |
Remove the F/PMP relay from the engine room No. 1 relay block.
Disconnect the ECM connector.
Disconnect the IA instrument panel junction block connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| F/PMP relay terminal 1 - B96-59 (FPR) | Below 1 Ω |
| F/PMP relay terminal 2 - IA-8 | Below 1 Ω |
| F/PMP relay terminal 3 - IA-8 | Below 1 Ω |
| F/PMP relay terminal 1 or B96-59 (FPR) - Body ground | 10 kΩ or higher |
| F/PMP relay terminal 2 or IA-8 - Body ground | 10 kΩ or higher |
| F/PMP relay terminal 3 or IA-8 - Body ground | 10 kΩ or higher |
Reconnect the ECM connector
Reconnect the instrument panel junction block connector.
Reinstall the F/PMP relay.
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (F/PMP - FUEL PUMP AND PUMP RESISTOR) |
![]() |
Remove the F/PMP relay from the engine room No. 1 relay block.
Disconnect the fuel pump connector.
Disconnect the fuel pump resistor connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| F/PMP relay terminal 4 - T1-4 | Below 1 Ω |
| F/PMP relay terminal 5 - A63-1 | Below 1 Ω |
| A63-2 - T1-4 | Below 1 Ω |
| T1-5 - Body ground | Below 1 Ω |
| F/PMP relay terminal 4 or T1-4 - Body ground | 10 kΩ or higher |
| F/PMP relay terminal 5 or A63-1 - Body ground | 10 kΩ or higher |
| A63-2 or T1-4 - Body ground | 10 kΩ or higher |
Reconnect the fuel pump resistor connector.
Reconnect the fuel pump connector.
Reinstall the F/PMP relay.
|
| ||||
| OK | |
| 10.INSPECT FUEL PUMP |
![]() |
Inspect fuel pump resistance.
Measure the resistance between the terminals.
Inspect fuel pump operation.
Apply the battery voltage to both the terminals. Check that the pump operates.
|
| ||||
| OK | |
| 11.INSPECT FUEL PUMP RESISTOR |
Measure the resistance of the fuel pump resistor.
|
| ||||
| OK | ||
| ||
| 12.READ VALUE USING INTELLIGENT TESTER (STARTER SIG) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned ON and START.
| Ignition Switch Position | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (ENGINE SPD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the tester while cranking.
|
| ||||
| OK | ||
| ||