Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1380    Stop Light Control Relay Malfunction

for Preparation Click here


DESCRIPTION

Upon receiving the downhill assist control or hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.

DTC Code
DTC Detection Condition
Trouble Area
C1380
Either of the following is detected:
  1. When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STPO) is on, a signal has not been input to the STP terminal for 5 seconds or more.
  2. When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STPO) is off, the signal at the STP is different from the input signal at the STP2 for 5 seconds or more.
  1. STOP fuse
  2. Stop light switch circuit
  3. Stop light control relay
  4. Stop light control relay (BRK)
  5. Stop light control relay circuit
  6. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM


C237064E05


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When C1425 is output together with C1380, inspect and repair the trouble areas indicated by C1425 first (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
INSPECT STOP LIGHT CIRCUIT (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 9
OK


3.INSPECT SKID CONTROL ECU (STP TERMINAL)


    C194130E19
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness in the locking part and connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-2 (STP) - Body ground
    Stop light switch off
    (Brake pedal released)
    Below 1.5 V
    Stop light switch on
    (Brake pedal depressed)
    8 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester (Click here).

    ABS/VSC/TRC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay (BRK)
    Relay ON / OFF
    Observe the stop lights.

  1. Check that the "ON" and "OFF" of the stop lights can be shown on the rear combination light by the intelligent tester.

    OK:
    The stop lights turn on or off in accordance with the intelligent tester.



NG
Go to step 6
OK


5.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC (C1380) is not output.
    A
    DTC (C1380) is output.
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

6.INSPECT STOP LIGHT CONTROL RELAY (BRK)


    C126459E12
  1. Turn the ignition switch off.

  1. Remove the stop light control relay (BRK).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 4
    Voltage is applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE STOP LIGHT CONTROL RELAY (BRK)
OK


7.INSPECT ENGINE ROOM NO. 1 RELAY BLOCK (POWER SOURCE TERMINAL)


    C194407E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Stop light control relay (BRK) terminal 5 - Body ground
    Always
    11 to 14 V
    Stop light control relay (BRK) terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


8.INSPECT SKID CONTROL ECU (STPO TERMINAL)


    C194130E21
  1. Install the stop light control relay (BRK).

  1. Make sure that there is no looseness in the locking part and connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-31 (STPO) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

9.INSPECT SKID CONTROL ECU (STP2 TERMINAL)


    C194130E22
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness in the locking part and connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-22 (STP2) - Body ground
    Stop light switch on (Brake pedal depressed)
    8 to 14 V
    Stop light switch off (Brake pedal released)
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)