DTC B1825/56 Short in Front Passenger Side - Side Squib Circuit |
DTC B1826/56 Open in Front Passenger Side - Side Squib Circuit |
DTC B1827/56 Short to GND in Front Passenger Side - Side Squib Circuit |
DTC B1828/56 Short to B+ in Front Passenger Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1825/56 | The center airbag sensor receives a line short signal 5 times in the front passenger side - side squib circuit during primary check. |
|
| B1826/56 | Center airbag sensor receives an open signal in the front passenger side - side squib circuit for 2 seconds. |
|
| B1827/56 | Center airbag sensor receives a short to ground signal in the front passenger side - side squib circuit for 0.5 seconds. |
|
| B1828/56 | Center airbag sensor receives a short to B+ signal in the front passenger side - side squib circuit for 0.5 seconds. |
|

| 1.CHECK FRONT PASSENGER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY (FRONT PASSENGER SIDE - SIDE SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag RH.
Connect SST (resistance 2.1) to connector E.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the No. 2 seat airbag wire connectors (on the front passenger side - side squib) are not damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (FRONT PASSENGER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| f1-1 (SFP+) - Body ground | Below 1 V |
| f1-2 (SFP-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| e1-1 (SFP+) - Body ground | Below 1 V |
| e1-2 (SFP-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| f1-1 (SFP+) - f1-2 (SFP-) | Below 1 Ω |
| f1-1 (SFP+) - Body ground | 1 MΩ or higher |
| f1-2 (SFP-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| e1-1 (SFP+) - e1-2 (SFP-) | Below 1 Ω |
| e1-1 (SFP+) - Body ground | 1 MΩ or higher |
| e1-2 (SFP-) - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| f1-1 (SFP+) - f1-2 (SFP-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| e1-1 (SFP+) - e1-2 (SFP-) | 1 MΩ or higher |
|
| ||||
| NG | |
| 4.CHECK NO. 2 SEAT AIRBAG WIRE |
![]() |
Disconnect the No. 2 seat airbag wire connector from the No. 2 floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| f1-1 (SFP+) - Body ground | Below 1 V |
| f1-2 (SFP-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| e1-1 (SFP+) - Body ground | Below 1 V |
| e1-2 (SFP-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| f1-1 (SFP+) - Lf1-1 | Below 1 Ω |
| f1-2 (SFP-) - Lf1-2 | Below 1 Ω |
| f1-1 (SFP+) - f1-2 (SFP-) | 1 MΩ or higher |
| f1-1 (SFP+) - Body ground | 1 MΩ or higher |
| f1-2 (SFP-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| e1-1 (SFP+) - Ke1-1 | Below 1 Ω |
| e1-2 (SFP-) - Ke1-2 | Below 1 Ω |
| e1-1 (SFP+) - e1-2 (SFP-) | 1 MΩ or higher |
| e1-1 (SFP+) - Body ground | 1 MΩ or higher |
| e1-2 (SFP-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||