Home › TRANSMISSION ยท U140F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY

AUTOMATIC TRANSAXLE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter (Click here).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch to the automatic transaxle.



    C083051E01
  1. Using a vernier caliper, measure dimension A between the transaxle and the end surface of the drive plate.



    C065911E01
  1. Using a vernier caliper and straightedge, measure the dimension B shown in the illustration and check that B is greater than A.

    Standard dimension:
    A + 1.0 mm (0.039 in.) or more



3. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


C133011E01
  1. Install the cable bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



4. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C133010E01
  1. Install the filler tube with the bolt.

  1. Install the filler tube with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the ATF dipstick.



5. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY


C127822E01
  1. Install the automatic transaxle with the 5 upper side mounting bolts to the engine.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt A
    46 N*m{ 469 kgf*cm , 34 ft.*lbf } for bolt B



    C127820
  1. Install the 4 lower side mounting bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    C129381
  1. Install the 6 torque converter clutch mounting bolts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    HINT:
    First install the green colored bolt and then the 5 bolts.

  1. Install the flywheel housing under cover.



6. INSTALL TRANSFER ASSEMBLY


    C126622
  1. except K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



    C130224
  1. for K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



7. INSTALL ENGINE MOUNTING BRACKET LH


C129380
  1. Install the mounting bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



8. INSTALL ENGINE MOUNTING BRACKET FR


C130924
  1. w/ Warmer:
    Install the mounting bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



    C130912
  1. for Water cooled:
    Install the mounting bracket with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for 14 mm head bolt

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for 12 mm head bolt



9. INSTALL ENGINE MOUNTING BRACKET RR


C130913
  1. Install the mounting bracket with the 3 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



10. INSTALL TRANSMISSION OIL COOLER (w/ Warmer)
  1. Install the oil cooler (Click here).



11. INSTALL TRANSMISSION OIL COOLER HOSE AND TUBE (for Water Cooled)
  1. Install the oil cooler hoses and tube (Click here).



12. CONNECT WIRE HARNESS


C127821
  1. Connect the wire harness clamps.

  1. Connect the 2 speed sensor connectors.

  1. Connect the transaxle wire connector.

  1. Connect the park/neutral position switch connector.



13. INSTALL STARTER ASSEMBLY


A124921
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    A124920
  1. Connect the starter wire with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the starter connector.

  1. Install the terminal nut and cover the nut with the cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 in.*lbf }



14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. for 1AZ-FE:
    Install the engine with transaxle (Click here).

  1. for 2AZ-FE:
    Install the engine with transaxle. (Click here).



15. ADD AUTOMATIC TRANSAXLE FLUID

Fluid type:
Toyota Genuine ATF WS



16. INSPECT AUTOMATIC TRANSAXLE FLUID
  1. Inspect the automatic transaxle fluid (Click here).



17. PERFORM RESET MEMORY
  1. Perform the RESET MEMORY procedures (A/T initialization) (Click here).