Home › DRIVE LINE › GF1A TRANSFER › TRANSFER CASE OIL SEAL (for LH Side)

TRANSFER CASE OIL SEAL (for LH Side) > REPLACEMENT

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. DRAIN TRANSFER OIL
  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }



3. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. for 1AZ-FE:
    Remove the engine assembly with transaxle (Click here).

  1. for 2AZ-FE:
    Remove the engine assembly with transaxle (Click here).

  1. for 2GR-FE:
    Remove the engine assembly with transaxle .

  1. for 3ZR-FAE:
    Remove the engine assembly with transaxle .



4. REMOVE REAR ENGINE MOUNTING BRACKET
  1. for U140F:
    Remove the rear engine mounting bracket .

  1. for E352F/E359F:
    Remove the rear engine mounting bracket .

  1. for U151F:
    Remove the rear engine mounting bracket .

  1. for EB61F:
    Remove the rear engine mounting bracket .

  1. for K111F:
    Remove the rear engine mounting bracket .



5. REMOVE TRANSFER ASSEMBLY


    C126622
  1. except K111F:
    Remove the 6 nuts, 2 bolts and transfer from the transaxle.



    C130224
  1. for K111F:
    Remove the 6 nuts and transfer from the transaxle.



6. REMOVE TRANSFER CASE OIL SEAL


C126623E01
  1. Using SST, tap out the transfer case oil seal.

    SST
    09308-00010  



7. INSTALL TRANSFER CASE OIL SEAL


C126624E01
  1. Using SST and a hammer, tap in the transfer case oil seal.

    SST
    09316-60011   (09316-00011)

    Standard depth:
    9.5 to 10.5 mm (0.37 to 0.41 in.)

    NOTICE:
    Do not damage the oil seal lip.

  1. Coat a new oil seal lip with MP grease.



8. INSTALL TRANSFER ASSEMBLY


    C126622
  1. except K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



    C130224
  1. for K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



9. INSTALL REAR ENGINE MOUNTING BRACKET
  1. for U140F:
    Install the rear engine mounting bracket .

  1. for E352F/E359F:
    Install the rear engine mounting bracket .

  1. for U151F:
    Install the rear engine mounting bracket .

  1. for EB61F:
    Install the rear engine mounting bracket .

  1. for K111F:
    Install the rear engine mounting bracket .



10. INSTALL TRANSAXLE WITH ENGINE ASSEMBLY
  1. for 1AZ-FE:
    Install the transaxle with engine assembly (Click here).

  1. for 2AZ-FE:
    Install the transaxle with engine assembly (Click here).

  1. for 2GR-FE:
    Install the transaxle with engine assembly .

  1. for 3ZR-FAE:
    Install the transaxle with engine assembly .



11. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }



12. INSPECT TRANSFER OIL


    C110905
  1. Remove the transfer case plug No. 2 (for filler) and gasket.

  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    Hypoid gear oil SX API GL-5 or equivalent

    Viscosity:
    SAE 85W-90

    Standard capacity:
    0.45 liter (0.48 US qts, 0.40 Imp. qts)

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then install the plug.

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


14. INSPECT SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).