Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the FLSH relay*1 (turn signal flasher relay *2).

HINT:
*1: for LHD
*2: for RHD


WIRING DIAGRAM


B129969E01


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control functions (Click here).

    OK:
    Each function of wireless door lock control system operates normally using transmitter switch.



OK
END
NG


2.CHECK TRANSMITTER LED ILLUMINATION
  1. Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.

    OK:
    Transmitter's LED illuminates 3 times when switch is pressed 3 times.



NG
Go to step 4
OK


3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS (STANDARD OPERATION FUNCTION)

HINT:
Use the following standard test procedure to check the transmitter again.

  1. Hold the transmitter approximately 1 m (3.28 ft.) from the driver side door outside handle. The transmitter must be held parallel to the ground and perpendicular to the side of the vehicle.

  1. Press and hold either the LOCK or UNLOCK transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

    OK:
    Doors can be locked and unlocked with transmitter switches.



NG
Go to step 5
OK


4.REPLACE TRANSMITTER BATTERY
  1. Temporarily replace the transmitter battery with a new or normally functioning one (Click here).

  1. Check that the doors can be locked and unlocked using the transmitter switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL TRANSMITTER MODULE
OK

END (TRANSMITTER BATTERY IS DEFECTIVE) 

5.CHECK ROOM LIGHT
  1. Check that the room light illumination operates normally.

    OK:
    Room light illumination operates normally.



NG
Go to LIGHTING SYSTEM
OK


6.SWITCH TO SELF-DIAGNOSTIC MODE
B110075E12
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch OFF). Then turn the ignition switch ON and OFF.

    3. Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch ON and OFF.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.

  1. Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.

    OK:
    Flash pattern is same as illustration.



NG
Go to step 11
OK


7.CHECK BY SELF-DIAGNOSTIC MODE

B137723E02

  1. Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.

    Result: 
    Result
    Proceed to
    Unmatching recognition code is output
    A
    Normal waves (light flash pattern) is output
    B
    No diagnosis outputs
    C



B
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)

C
Go to step 9
A


8.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 15
OK

END 

9.CHECK DOOR CONTROL TRANSMITTER (RESPONSE)
  1. Temporarily replace the door control receiver with a new or normally functioning one.

  1. Held down the door control transmitter's switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



OK
REPLACE DOOR CONTROL TRANSMITTER MODULE
NG


10.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Temporarily replace the door control receiver (Click here, Click here) with a new or normally functioning one.

  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

11.CONFIRM PROCEDURES TO ENTER SELF-DIAGNOSTIC MODE
Result: 
Result
Proceed to
Self-diagnostic mode entry successful
A
Self-diagnostic mode entry unsuccessful
B


B
Go to step 6
A


12.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
B110401E01
  1. Remove the switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    Pushed
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


13.CHECK WIRE HARNESS (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)
B133177E02
  1. Disconnect the L9 switch connector.

  1. Disconnect the E20 junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    L9-1 - IE-26 (KSW)
    Below 1 Ω
    L9-2 - Body ground
    L9-1 or IE-26 (KSW) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


14.CHECK DOOR CONTROL RECEIVER (OUTPUT)
B111368E09
  1. Reconnect the L10 receiver connector.

  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    L10-2 (RDA) - Body ground
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    Below 1 V → 6 to 7 V → Below 1 V



OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
NG


15.CHECK DOOR CONTROL TRANSMITTER MODULE (OPERATION)
  1. Temporarily replace the door control transmitter module with a new or normally functioning one (Click here).

  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL RECEIVER
OK

END (DOOR CONTROL TRANSMITTER MODULE IS DEFECTIVE)