Home › BODY › INTERIOR › ROOF HEADLINING (for Short Body)

ROOF HEADLINING (for Short Body) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT DOOR SCUFF PLATE LH


    B129699
  1. Using a screwdriver, detach the 10 claws and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



4. REMOVE COWL SIDE TRIM BOARD LH


B129697
  1. Remove the cap nut.

  1. Using a screwdriver, detach the 3 claws and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip.



7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the front door opening trim weatherstrip.



8. REMOVE FRONT PILLAR GARNISH LH


    B309798
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 3 guides. Then remove the front pillar garnish.



  1. w/ Curtain Shield Airbag:



      B309719E01
    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      HINT:
      Make the front pillar garnish hang down from the front pillar garnish clip.



    2. B309720E01
    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish.

      NOTICE:
      1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
      2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      HINT:
      Tape the tips of the needle-nose pliers before use.

    4. Detach the 3 guides and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wiring harness clamps.



    B065292E06
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



9. REMOVE FRONT PILLAR GARNISH RH


    B181999
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 3 guides. Then remove the front pillar garnish.



  1. w/ Curtain Shield Airbag:



      B309614E01
    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      HINT:
      Make the front pillar garnish hang down from the front pillar garnish clip.



    2. B309615E01
    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish.

      NOTICE:
      1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
      2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      HINT:
      Tape the tips of the needle-nose pliers before use.

    4. Detach the 3 guides and remove the front pillar garnish.



    B135443
  1. Using a clip remover, remove the 4 antenna cord clamps.



    B131254E01
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



10. REMOVE UPPER INSTRUMENT PANEL
  1. Remove the upper instrument panel (Click here).



11. REMOVE REAR DOOR SCUFF PLATE LH


    B129711
  1. Using a screwdriver, detach the 8 claws and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip.



14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Remove the rear door opening trim weatherstrip.



15. REMOVE LOWER CENTER PILLAR GARNISH LH


  1. Disconnect the front seat outer belt's floor anchor.

    1. Remove the anchor cover.



    2. B137545
    3. Remove the bolt and disconnect the floor anchor.



    B129700
  1. Using a screwdriver, detach the 2 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 2 clips and remove the garnish.



16. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE CENTER PILLAR GARNISH LH


B129701
  1. Remove the 2 screws.

  1. Using a clip remover, detach the clip and remove the garnish.



18. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



19. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY
  1. Remove the package tray trim pocket.



20. REMOVE TONNEAU COVER ASSEMBLY
  1. Remove tonneau cover.



21. REMOVE REAR FLOOR NO. 1 BOARD
  1. Remove the rear floor No. 1 board.



22. REMOVE DECK BOARD ASSEMBLY
  1. Remove the deck board.



23. REMOVE REAR FLOOR NO. 3 BOARD
  1. Remove the rear floor No. 3 board.



24. REMOVE REAR FLOOR NO. 2 BOARD
  1. Remove the rear floor No. 2 board.



25. REMOVE JACK CARRIER ASSEMBLY


B129715
  1. Using a clip remover, remove the 7 clips and remove the jack carrier.



26. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE


B129717
  1. Remove the 4 screws.

  1. Using a clip remover, detach the 7 clips and remove the plate.



27. REMOVE BACK DOOR WEATHERSTRIP
  1. Remove the back door weatherstrip.



28. REMOVE REAR FLOOR FINISH PLATE


    B129716
  1. Using a clip remover, detach the 6 clips and remove the finish plate.



29. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH


    B132537
  1. Using a screwdriver, detach the 6 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.



30. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH


    B135482
  1. Using a screwdriver, detach the 6 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.



31. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


B131613
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



32. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET


    B130163
  1. Remove the bolt, 2 washers, collar and bracket.



33. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    B137546
  1. Disconnect the rear No. 1 seat belt's floor anchor.

    1. Remove the anchor cover.

    2. Remove the bolt and disconnect the floor anchor.



    B129712
  1. Remove the bolt and 2 screws.

  1. Using a screwdriver, detach the 5 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the trim board.

  1. Disconnect the power outlet socket connector.

  1. Remove the belt hanger.



34. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    B137547
  1. Disconnect the rear No. 1 seat belt's floor anchor.

    1. Remove the anchor cover.

    2. Remove the bolt and disconnect the floor anchor.



    B129713
  1. Remove the bolt and 2 screws.

  1. Using a screwdriver, detach the 5 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the trim board.

  1. Remove the belt hanger.



35. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH


    B129714
  1. Using a clip remover, detach the 7 clips and remove the garnish.



36. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



37. REMOVE REAR ROOM PARTITION NET HOOK LH


    B129710
  1. Remove the 2 screws and net hook.



38. REMOVE REAR ROOM PARTITION NET HOOK RH

HINT:
Use the same procedure described for the LH side.



39. REMOVE VISOR ASSEMBLY LH


    B131005
  1. Using a screwdriver, detach the 4 claws and remove the visor bracket cover.

    HINT:
    Tape the screwdriver tip before use.



    B131006E01
  1. Remove portion A from the visor holder.

  1. Detach the 2 claws and remove the visor.



40. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



41. REMOVE VISOR HOLDER


    B050596E06
  1. Remove the visor holder by turning it counterclockwise.



42. REMOVE VANITY LIGHT ASSEMBLY


    B131423
  1. Using a screwdriver, pry out the vanity light assembly.

    HINT:
    Tape the screwdriver tip before use.



    B131425
  1. Detach the 2 claws and vanity light.



43. REMOVE MAP LIGHT ASSEMBLY


B131951
  1. Detach the 4 clips and remove the map light.

  1. Disconnect the light connector.



44. REMOVE ROOM LIGHT ASSEMBLY


    B131448
  1. Using a screwdriver, detach the 4 claws and remove the 2 covers.

    HINT:
    Tape the screwdriver tip before use.



    B131449E01
  1. Remove the bulb from the room light switch base.



    B132733
  1. Using a screwdriver, detach the 4 claws and remove the light.

    HINT:
    Tape the screwdriver tip before use.



    B131451
  1. Using a screwdriver, detach the 4 claws and remove the room light switch base.

    HINT:
    Tape the screwdriver tip before use.



45. REMOVE ASSIST GRIP COVER (for Front Grip)


    B131002
  1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



46. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B131003
  1. Detach the 4 claws and remove the assist grip.



47. REMOVE ASSIST GRIP COVER (for Rear Grip)


    B131002
  1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



48. REMOVE REAR ASSIST GRIP ASSEMBLY


    B131004
  1. Detach the 4 claws and remove the assist grip.



49. REMOVE SHOULDER BELT ANCHOR COVER RH


B133646E01
  1. Using a screwdriver, remove the 4 claws and cover.

    HINT:
    Tape the screwdriver tip before use.



50. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
  1. Remove the sun roof opening trim moulding.



51. REMOVE ROOF HEADLINING ASSEMBLY


    B131381
  1. Disconnect the No. 1 roof wire harness.

    1. Using a screwdriver, remove the wire harness clamp.

    2. Disconnect the roof wire connector.



  1. Disconnect the antenna cord sub-assembly.



      B135492
    1. Disconnect the antenna cord connector from the front pillar RH.



    2. B135485
    3. Disconnect the 2 antenna cord connectors from the rear pillar RH.

    4. Using a clip remover, remove the wiring harness clamp.

    5. Remove the bracket's bolt.



    B130235E02
  1. w/o Sliding Roof:

    1. Using a clip remover, remove the 4 clips and headlining.

  1. w/ Sliding Roof:

    1. Disconnect the connector from the drive gear.

    2. Using a clip remover, remove the 2 clips and headlining.



52. REMOVE NO. 1 ROOF WIRE
  1. Only when replacing the roof headlining:

    1. Remove the double-sided tape and roof wire.



53. REMOVE ANTENNA CORD SUB-ASSEMBLY


  1. for Short Body (w/o Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134704E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Short Body (w/ Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134706E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Long Body (w/o Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134708E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Long Body (w/ Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134710E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



54. REMOVE NO. 1 ROOF SILENCER PAD (w/ Sliding Roof)
  1. Remove the 3 silencer pads.



55. REMOVE NO. 3 ROOF SILENCER PAD
  1. Remove the 2 silencer pads.