DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
DTC P0174 System Too Lean (Bank 2) |
DTC P0175 System Too Rich (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 P0174 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 P0175 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0171, P0172, P0174 or P0175 | A |
| P0171, P0172, P0174 or P0175 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 3.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F Sensor Condition | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | C |
| Lean/Lean | Lean/Lean | Actual air-fuel ratio lean |
| A |
| Rich/Rich | Rich/Rich | Actual air-fuel ratio rich |
| A |
| Lean/Lean | Lean/Rich | A/F sensor malfunction | A/F sensor | B |
| Rich/Rich | Lean/Rich | A/F sensor malfunction | A/F sensor | B |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2500 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAKS |
|
| ||||
| OK | |
| 9.CHECK FOR SPARKS AND IGNITION |
Check for sparks and ignition .
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Inspect the fuel injector assembly (Click here).
|
| ||||
| OK | |
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | Always | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 12.INSPECT INTEGRATION RELAY (A/F RELAY) |
![]() |
Remove the integration relay from the engine room No. 1 relay block.
Measure the A/F relay resistance.
| Tester Connection | Specified Condition |
| 1C-1 - 1B-8 | 10 kΩ or higher |
| 1C-1 - 1B-8 | Below 1 Ω (when battery voltage is applied to terminals 1B-6 and 1B-7) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B96-86) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B96-93) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B96-116) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA2A (B67-1) - HA2A (B96-109) | Below 1 Ω |
| A2A+ (B67-3) - A2A+ (B96-120) | Below 1 Ω |
| A2A- (B67-4) - A2A- (B96-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B96-86) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B96-93) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B96-116) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (B67-1) or HA2A (B96-109) - Body ground | 10 kΩ or higher |
| A2A+ (B67-3) or A2A+ (B96-120) - Body ground | 10 kΩ or higher |
| A2A- (B67-4) or A2A- (B96-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3 (Procedure A).
Turn the ignition switch to the ON position and turn the tester on (Procedure B).
Clear the DTCs (Click here) (Procedure C).
Select the check mode using the tester (Click here) (Procedure D).
Start the engine and warm it up with all the accessories switched off (Procedure E).
Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes (Procedure F).

| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175) |
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171, P0172, P0174 or P0175 | B |
|
| ||||
| A | ||
| ||
| 17.INSPECT FUSE (A/F FUSE) |
![]() |
Remove the A/F fuse from the integration relay.
Measure the fuse resistance.
Reinstall the fuse.
|
| ||||
| OK | ||
| ||