VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| CHECK SENSOR SIGNAL BY TEST MODE (When Using Intelligent Tester) |
Procedures for test mode:
Turn the ignition switch off.
Check that the steering wheel is in the centered position.
except M/T:
Check that the shift lever is in P.
Apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Set the intelligent tester to test mode (select "Signal Check").
Check that the ABS warning light and slip indicator light blink as shown in the illustration.
![]() |
| Section Title | See Procedure |
| ABS Warning Light does not Come ON |
Click here
|
| Slip Indicator Light does not Come ON |
Click here
|
| TS and CG Terminal Circuit |
Click here
|
Start the engine.
w/ Downhill Assist Control:
Check the lost booster pressure judgment and perform the master cylinder pressure sensor zero point calibration.
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more (lost booster pressure judgment).
Start the engine while depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more.
Check that the brake warning light goes off when quickly releasing the brake pedal (normal booster pressure judgment).
Leave the vehicle for 1 second or more (master cylinder pressure sensor zero point calibration).
Check the deceleration sensor.
Keep the vehicle stationary on a level surface for 1 second or more.
Check the master cylinder pressure sensor.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light remains illuminated for 3 seconds.
Check the speed sensor.
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.

Check the yaw rate sensor.
except M/T:
Move the shift lever to P.
Pull the parking brake lever.
![]() |
Check that the slip indicator light is blinking as shown in the illustration.
Keep the vehicle stationary on a level surface for 1 second or more.
except M/T:
Move the shift lever to D.
![]() |
Drive the vehicle at a speed of 5 km/h (3 mph) or more, and turn the steering wheel either to the left or right 90° or more for 1 second or more to turn the vehicle through 180°.
Stop the vehicle.
except M/T:
Move the shift lever to P.
Apply the parking brake.
Check that the skid control buzzer sounds for 3 seconds.
Check the VSC OFF switch.
![]() |
Check that the slip indicator light is blinking as shown in the illustration.
for 2WD:
Check that the AUTO LSD indicator light turns on when the VSC OFF switch is pressed briefly.
for 4WD with multi information display:
Check that the TRC OFF indicator on the multi information display turns off when the VSC OFF switch is pressed briefly.
for 4WD without multi information display:
Check that the TRC OFF indicator light turns off when the VSC OFF switch is pressed briefly.
Briefly press the VSC OFF switch again.
Check the completion of sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
Read the DTCs of signal check function.
Read the DTC(s) by following the instructions on the intelligent tester screen.
| CHECK SENSOR SIGNAL BY TEST MODE (When not Using Intelligent Tester) |
Procedures for test mode:
Turn the ignition switch off.
Check that the steering wheel is in the centered position.
except M/T:
Check that the shift lever is in P.
Apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
![]() |
Check that the ABS warning light and slip indicator light blink as shown in the illustration.
| Section Title | See Procedure |
| ABS Warning Light does not Come ON |
Click here
|
| Slip Indicator Light does not Come ON |
Click here
|
| TS and CG Terminal Circuit |
Click here
|
Start the engine.
w/ Downhill Assist Control:
Check the lost booster pressure judgment and perform the master cylinder pressure sensor zero point calibration.
Turn the ignition switch to ON.
Check that the brake warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more (lost booster pressure judgment).
Start the engine while depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more.
Check that the brake warning light goes off when quickly releasing the brake pedal (normal booster pressure judgment).
Leave the vehicle for 1 second or more (master cylinder pressure sensor zero point calibration).
Check the deceleration sensor.
Keep the vehicle stationary on a level surface for 1 second or more.
Check the master cylinder pressure sensor.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light remains illuminated for 3 seconds.
Check the speed sensor.
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the speed sensor signal.

Check the yaw rate sensor.
except M/T:
Move the shift lever to P.
Pull the parking brake lever.
![]() |
Check that the slip indicator light is blinking as shown in the illustration.
Keep the vehicle stationary on a level surface for 1 second or more.
except M/T:
Move the shift lever to D.
![]() |
Drive the vehicle at a speed of 5 km/h (3 mph) or more, and turn the steering wheel either to the left or right 90° or more for 1 second or more to turn the vehicle through 180°.
Stop the vehicle.
except M/T:
Move the shift lever to P.
Apply the parking brake.
Check that the skid control buzzer sounds for 3 seconds.
Check the VSC OFF switch.
![]() |
Check that the slip indicator light is blinking as shown in the illustration.
for 2WD:
Check that the AUTO LSD indicator light turns on when the VSC OFF switch is pressed briefly.
for 4WD with multi information display:
Check that the TRC OFF indicator on the multi information display turns off when the VSC OFF switch is pressed briefly.
for 4WD without multi information display:
Check that the TRC OFF indicator light turns off when the VSC OFF switch is pressed briefly.
Briefly press the VSC OFF switch again.
Check the completion of sensor check.
When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.
Read the DTCs of the signal check function.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Count the number of blinks of the ABS and slip indicator lights.

After the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
| DTC OF TEST MODE FUNCTION (SIGNAL CHECK) |
| DTC Code | Detection Item | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH |
|
| C1276/76 | Abnormal change in output signal of front speed sensor LH |
|
| C1277/77 | Abnormal change in output signal of rear speed sensor RH |
|
| C1278/78 | Abnormal change in output signal of rear speed sensor LH |
|
| C1279/79 | Deceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction | Master cylinder pressure sensor |
| Booster failure detection (w/ Booster Failure Compensation) | Brake pedal load sensing switch |
| DTC Code | Detection Item | Trouble Area |
| C0371/71 | Yaw rate sensor | Yaw rate sensor |
| C1379/74* | Downhill assist control switch | Downhill assist control switch |
![]() |