ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
![]() |
Check that the engine coolant is between the LOW and FULL lines when the engine is cold.
If the level is low, check for leakage and add TOYOTA Super Long Life Coolant (SLLC) or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology up to the FULL line.
| 2. INSPECT ENGINE OIL |
Warm up the engine, and then stop the engine and wait for 5 minutes.
Check that the oil level is between the dipstick low level mark and full level mark.
If the level is low, check for leakage and add oil up to the full level mark.
| 3. INSPECT BATTERY |
Check the battery for damage or deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the electrolyte quantity of each cell.
For maintenance-free batteries:
![]() |
For non-maintenance-free batteries:
Check the battery voltage.
Turn the engine switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.
![]() |
Measure the battery voltage between the negative (-) and positive (+) terminals of the battery.
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner cap.
Remove the air filter element.
Visually check that the air filter is not excessively damaged or oily.
If necessary, replace the air cleaner filter element.
| 5. INSPECT SPARK PLUG |
![]() |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
| *1 | Ground |
Alternative inspection method:
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plug.
![]() |
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its thread and insulator.
If there is any damage, replace the spark plug.
| Manufacturer | Product |
| DENSO | SC20HR11 |
Reference:
![]() |
Check the spark plug electrode gap.
Clean the spark plug.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
| 6. INSPECT V-RIBBED BELT |
![]() |
Check the belt for wear, cracks or other signs of damage.
If any of the following defects is found, replace the V-ribbed belt.
![]() |
Check that the belt fits properly in the ribbed grooves.
![]() |
Check the V-ribbed belt deflection and tension.
| Item | Specified Condition |
| New belt | 7.0 to 8.2 mm (0.276 to 0.323 in.) |
| Used belt | 7.6 to 10.0 mm (0.299 to 0.394 in.) |
| Item | Specified Condition |
| New belt | 700 to 800 N (70 to 80 kgf, 157.4 to 179.8 lbf) |
| Used belt | 550 to 750 N (55 to 75 kgf, 123.6 to 168.6 lbf) |
| 7. INSPECT VALVE LASH ADJUSTER NOISE |
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.
If any defects or problems are found during the inspection above, perform a lash adjuster inspection .
| 8. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using an intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
When not using the intelligent tester:
Remove the No. 2 cylinder head cover.
![]() |
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Start the engine and idle it.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | Front view of DLC3 |
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover.
| 9. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Item | Specified Condition |
| for Manual Transaxle | 580 to 680 rpm |
| for CVT | 600 to 700 rpm |
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
![]() |
When not using the intelligent tester:
| *1 | Front view of DLC3 |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
Check the idle speed.
| Item | Specified Condition |
| for Manual Transaxle | 580 to 680 rpm |
| for CVT | 600 to 700 rpm |
Disconnect the tachometer probe from the DLC3.
| 10. INSPECT COMPRESSION |
Warm up and stop the engine.
Check for DTCs (Click here).
Remove the No. 2 cylinder head cover.
Remove the 4 bolts and 4 ignition coils.
Remove the 4 spark plugs.
Disconnect the 4 fuel injector connectors.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
| *1 | Compression Gauge |
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Install the 4 ignition coils with the 4 bolts.
Install the No. 2 cylinder head cover.
Clear the DTCs (Click here).
| 11. INSPECT CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration during idling and when the engine is running at 2500 rpm.
Check the air fuel ratio sensor and heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|