Home › TRANSMISSION · K111F CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM

DTC    P0962    Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1)

DTC    P0963    Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1)

DTC    P0966    Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2)

DTC    P0967    Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2)


DESCRIPTION

Using shift solenoid valve DS1 (inflow to the primary pulley) and shift solenoid valve DS2 (outflow from the primary pulley), the ECM controls the line pressure and fluid volume input to and output from the primary pulley according to the vehicle speed and accelerator pedal angle. As a fail-safe function, if a solenoid is shorted or open, the ECM stops current to the faulty solenoid.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0962
  1. The vehicle is driven so that gear ratio changes occur.
  2. There is a short circuit in the shift solenoid valve DS1 circuit.
  3. 20 times
  4. 1 trip detection logic
  1. Short in shift solenoid valve DS1 circuit
  2. Continuously variable transaxle assembly
  3. ECM
P0963
  1. The vehicle is driven so that gear ratio changes occur.
  2. There is an open circuit in the shift solenoid valve DS1 circuit.
  3. 20 times
  4. 1 trip detection logic
  1. Open in shift solenoid valve DS1 circuit
  2. Continuously variable transaxle assembly
  3. ECM
P0966
  1. The vehicle is driven so that gear ratio changes occur.
  2. There is a short circuit in the shift solenoid valve DS2 circuit.
  3. 20 times
  4. 1 trip detection logic
  1. Short in shift solenoid valve DS2 circuit
  2. Continuously variable transaxle assembly
  3. ECM
P0967
  1. The vehicle is driven so that gear ratio changes occur.
  2. There is an open circuit in the shift solenoid valve DS2 circuit.
  3. 20 times
  4. 1 trip detection logic
  1. Open in shift solenoid valve DS2 circuit
  2. Continuously variable transaxle assembly
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the shift solenoid valve DS1 or DS2 circuit. When there is an open or short circuit in the shift solenoid valve DS1 or DS2 circuits, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM


C200618E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE SHIFT POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. In accordance with the display on the tester, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operates the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
    Reference gear ratios:
    1st (2.4) - 2nd (1.5) - 3rd (1.0) - 4th (0.7) - 5th (0.43)
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Used to check the operation of the shift solenoid valves.

    NOTICE:
    Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.

    [Vehicle Condition]
    50 km/h (30 mph) or less
    Result 
    Result
    Proceed to
    Gear ratio does not change
    A
    Gear ratio changes
    B



B
Go to step 6
A


2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)


    C199169E02
  1. Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (DS1) - Body ground
    20°C (68°F)
    11 to 13 Ω
    10 (DS2) - Body ground
    20°C (68°F)
    11 to 13 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Transmission Wire)



NG
Go to step 8
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C197707E28
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-55 (DS2) - Body ground
    20°C (68°F)
    11 to 13 Ω
    B32-56 (DS1) - Body ground
    20°C (68°F)
    11 to 13 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5.PERFORM INITIALIZATION

NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).

  1. Check that no DTC is stored.


NEXT

END 

6.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


7.PERFORM INITIALIZATION

NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).

  1. Check that no DTC is stored.


NEXT

END 

8.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
  1. Replace the continuously variable transaxle assembly (Click here).


NEXT


9.PERFORM INITIALIZATION

NOTICE:
  1. Performing reset memory will clear the learned values of both the yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor assembly*1 or deceleration sensor*2 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:
    Replaced Part
    1. Continuously variable transaxle assembly
    2. ECM
    3. Oil pressure sensor
    4. Yaw rate sensor assembly (w/ VSC)
    5. Deceleration sensor (w/o VSC)
    6. Brake actuator assembly (skid control ECU)
  2. After performing reset memory, always perform yaw rate sensor assembly*1 or deceleration sensor*2 (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.
  3. Always perform 0 point calibration with the vehicle on level ground.
  4. Do not shake or vibrate the vehicle during 0 point calibration.

  1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).

  1. Check that no DTC is stored.


NEXT

END