DTC P1589 Acceleration Sensor Learning Value |
| DTC Code | DTC Detection Condition
| Trouble Area |
| P1589 |
| Deceleration sensor 0 point calibration has not been performed |
|
|
| 1.PERFORM INITIALIZATION (DECELERATION SENSOR 0 POINT CALIBRATION) |
Turn the ignition switch off.
Move the shift lever to P and apply the parking brake.
Connect the tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor 0 Point Calibration.
| Result | Proceed to |
| Deceleration sensor 0 point calibration is completed normally | A |
| P1589 is output | B |
|
| ||||
| A | |
| 2.PERFORM INITIALIZATION (CVT OIL PRESSURE CALIBRATION) |
Turn the ignition switch off and wait at least 30 seconds.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and wait at least 2 seconds.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Start the engine and wait at least 5 seconds.
Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.
Check that no DTC is stored.
| NEXT | ||
| ||
| 3.INSPECT YAW RATE SENSOR ASSEMBLY AND DECELERATION SENSOR |
Check the yaw rate sensor assembly*1 or deceleration sensor*2 for any inclination, bracket deformation or installation clearance.
| Result | Proceed to |
| OK | A |
| NG (w/ VSC) | B |
| NG (w/o VSC) | C |
|
| ||||
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (G SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| G sensor | Converted output voltage of yaw rate sensor assembly*1 or deceleration sensor*2/ min.: 0 V max.: 5 V | Displays converted voltage of yaw rate sensor assembly*1 or deceleration sensor*2
| - |
| Result | Proceed to |
| Data displayed is as specified under Normal Condition | A |
| Data displayed is not as specified under Normal Condition (w/ VSC) | B |
| Data displayed is not as specified under Normal Condition (w/o VSC) | C |
|
| ||||
|
| ||||
| A | |
| 5.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 6.PERFORM INITIALIZATION |
| Replaced Part |
|
Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).
Check that no DTC is stored.
| NEXT | ||
| ||
| 7.REPLACE YAW RATE SENSOR ASSEMBLY |
Replace the yaw rate sensor assembly (Click here).
| NEXT | |
| 8.PERFORM INITIALIZATION |
| Replaced Part |
|
Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).
Check that no DTC is stored.
| NEXT | ||
| ||
| 9.REPLACE DECELERATION SENSOR |
Replace the deceleration sensor (Click here).
| NEXT | |
| 10.PERFORM INITIALIZATION |
| Replaced Part |
|
Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration (Click here).
Check that no DTC is stored.
| NEXT | ||
| ||