Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P104A    Valvematic SDOWN Circuit Malfunction

for Preparation Click here


DESCRIPTION

The ECM turns the power supply to the continuously variable valve lift controller assembly on/off. Normally, when the ignition switch is ON, +B voltage is constantly supplied to the continuously variable valve lift controller assembly. However, when a malfunction is detected in the VALVEMATIC system, the ECM turns the power supply to the continuously variable valve lift controller assembly off. The power supply is turned on/off through the shutdown (SDOWN) signal line between the ECM and continuously variable valve lift controller assembly. When the ignition switch is turned to ON, the ECM turns the shutdown (SDOWN) signal on (Hi) which turns the continuously variable valve lift controller assembly power on. Also, when the ignition switch is off or during fail-safe mode, the shutdown (SDOWN) signal is turned off (Lo) which turns the continuously variable valve lift controller assembly power off.
The ECM electronically monitors whether on/off switching is actually being performed in the ECM output circuit.

DTC No.
DTC Detection Condition
Trouble Area
P104A
The shutdown (SDOWN) signal line has an open circuit, or a short circuit to +B or ground (1 trip detection logic).
  1. A shutdown (SDOWN) signal line open circuit or short circuit to +B: While the ignition switch is off, even though the CPU in the ECM requests shutdown (SDOWN) signal Lo, the monitor detects Hi.
  2. Short circuit (short circuit to ground): While the ignition switch is ON, even though the CPU in the ECM requests shutdown (SDOWN) signal Hi, the monitor detects Lo.
  1. Open or short in continuously variable valve lift controller circuit
  2. ECM

WIRING DIAGRAM


A205143E04


INSPECTION PROCEDURE


NOTICE:
When one of the following DTCs is stored and the MIL is illuminated, DTC P1047 is stored and actuator position learning is performed every time the engine is started. Also, after the system returns to normal, the following occurs during the first driving cycle: 1) DTC P1047 is stored, 2) actuator position learning is performed and 3) the MIL illuminates during actuator position learning.

Actuator position learning is performed when these DTCs are stored.
P1046, P1049, P104A, P1055, P2646, P2647, P2648, P2649, P264A, U011B

HINT:
  1. If DTC P1047 is output at the same time as DTC P104A, disregard DTC P1047 and proceed with the inspection.
  2. After performing repairs, perform the following procedures and check that DTCs are not output again.

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON
  3. Turn the tester on.
  4. Clear the DTCs.
  5. Turn the ignition switch off.
  6. Turn the ignition switch to ON and wait 5 seconds.
  7. Turn the ignition switch off and wait 10 seconds.
  8. Turn the ignition switch to ON.
  9. Enter the following menus: Powertrain / Engine and ECT / DTC.
  10. Read the DTCs.
1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTC.

    Result 
    Result
    Proceed to
    DTC P104A is output
    A
    DTC P1049 is output at same time as DTC P104A
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER - ECM)


    A208660E03
  1. Disconnect the continuously variable valve lift controller assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A12-37 (SDWN) - B127-3 (SDWN)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A12-37 (SDWN) or B127-3 (SDWN) - Body ground
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Continuously Variable Valve Lift Controller)
    *2
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER - ECM)
OK

REPLACE ECM (Click here)