Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Microphone Circuit between Microphone and Navigation Receiver Assembly

for Preparation Click here


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.
It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM


E182423E02


E185279E01


INSPECTION PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY


  1. for 3ZR-FAE:



      E179201E03
    1. Disconnect the E106 navigation receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      13 (MIN-) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (MACC) - Body ground
      Ignition switch ACC
      4.75 to 5.25 V



  1. except 3ZR-FAE:



      E182693E02
    1. Disconnect the E54 navigation receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      17 (MACC) - Body ground
      Ignition switch ACC
      4.75 to 5.25 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - MAP LIGHT)


  1. for 3ZR-FAE:



      E179014E14
    1. Disconnect the E106 navigation receiver assembly connector.



    2. E130091E13
    3. Disconnect the R8 map light connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E106-5 (MACC) - R8-12 (ACC)
      Always
      Below 1 Ω
      E106-4 (MIN+) - R8-11 (MI1+)
      Always
      Below 1 Ω
      E106-13 (MIN-) - R8-10 (MIC-)
      Always
      Below 1 Ω
      E106-5 (MACC) - Body ground
      Always
      10 kΩ or higher
      E106-4 (MIN+) - Body ground
      Always
      10 kΩ or higher
      E106-13 (MIN-) - Body ground
      Always
      10 kΩ or higher
      E106-3 (SNS2) - Body ground
      Always
      Below 1 Ω



  1. except 3ZR-FAE:



      E182692E01
    1. Disconnect the E54 navigation receiver assembly connector.



    2. E130091E13
    3. Disconnect the R8 map light connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E54-17 (MACC) - R8-12 (ACC)
      Always
      Below 1 Ω
      E54-19 (MIC+) - R8-11 (MI1+)
      Always
      Below 1 Ω
      E54-20 (MIC-) - R8-10 (MIC-)
      Always
      Below 1 Ω
      E54-17 (MACC) - Body ground
      Always
      10 kΩ or higher
      E54-19 (MIC+) - Body ground
      Always
      10 kΩ or higher
      E54-20 (MIC-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE TELEPHONE MICROPHONE WITH ANOTHER AND CHECK
  1. Replace the telephone microphone with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END (TELEPHONE MICROPHONE IS FAULTY)