Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crank angle sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0335 Crankshaft Position Sensor "A" Circuit One of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to ECM while cranking.

·

No crankshaft position sensor signal to ECM while engine running.

·

Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0339 Crankshaft Position Sensor "A" Circuit Intermittent All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or higher.
(b) No crankshaft position sensor signal for 0.05 seconds or more.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM


- DTC stored DTC for Mexico Models
- Applies

A254145
2.979,1 3.333,1.198 0.354,0.198 10 GND 0.063,0.063 0.604,0.24 0.542,0.177 10 5 V/DIV. 1.219,1.917 1.969,2.063 0.75,0.146 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:

Grounding failure of the shielded wire may cause noise in the waveforms.


ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Related DTCs P0335: Crankshaft position sensor range check/rationality
P0335: Crankshaft position sensor verify pulse input
Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous
Duration -: Verify pulse input case 1
4.7 seconds: Verify pulse input case 2
0.016 seconds: Range check/rationality
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None

P0335: Crankshaft Position Sensor Range Check/Rationality
All of the following conditions are met -
Ignition switch ON
Time after starter off to on 3 seconds or more
Number of camshaft position sensor signal pulses 6 times
Battery voltage 7 V or higher
Minimum battery voltage while starter on Less than 11 V
Camshaft position sensor circuit fail Not detected

P0335: Crankshaft Position Sensor Verify Pulse Input Case 1
All of the following conditions are met -
Starter Off
Engine speed (Top dead center) 600 rpm or higher
Engine speed (30°CA) 600 rpm or higher
Time after starter from on to off 3 seconds or more

P0335: Crankshaft Position Sensor Verify Pulse Input Case 2
Both of the following conditions are met -
Starter On
Minimum battery voltage while starter on Below 11 V

TYPICAL MALFUNCTION THRESHOLDS

P0335: Crankshaft Position Sensor Range Check/Rationality
Number of crankshaft position sensor signal pulses 132 times or less, or 174 times or more

P0335: Crankshaft Position Sensor Verify Pulse Input Case 1 and Case 2
Engine speed signal No signal

COMPONENT OPERATING RANGE

Crankshaft position sensor
·

Crankshaft position sensor output voltage fluctuates while crankshaft revolving

·

34 crankshaft position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335 or P0339.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A255252
0.625,2.01 2.354,2.177 1.729,0.167 10 Crankshaft Position Sensor 5.656,2.25 6.021,2.417 0.365,0.167 10 ECM 0.625,1.854 0.927,2.021 0.302,0.167 10 B28 5.083,0.729 5.26,0.875 0.177,0.146 10 76 5,1.51 5.26,1.656 0.26,0.146 10 109 5.656,2.104 5.938,2.26 0.281,0.156 10 B77 5.344,0.708 5.635,0.854 0.292,0.146 10 NE+ 5.344,1.542 5.635,1.688 0.292,0.146 10 NE- 1.646,0.708 1.865,0.854 0.219,0.146 10 NE 1.615,1.542 1.885,1.688 0.271,0.146 10 NE- 2,0.74 2.104,0.906 0.104,0.167 10 1 2,1.49 2.115,1.656 0.115,0.167 10 2 3.229,1.729 3.802,1.917 0.573,0.188 10 Shielded

CAUTION / NOTICE / HINT

HINT:

After performing the procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.

·

Installation condition of the camshaft position sensor

·

Installation condition of the camshaft

·

Connection of the camshaft position sensor connector



HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the Techstream. To perform the check, follow the procedures below:

1.

Connect the Techstream to the DLC3.

2.

Start the engine.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Start the engine.


f.

Read the values displayed on the Techstream while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the Techstream.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B28-1 (NE) - B77-76 (NE+) Always Below 1 Ω
B28-2 (NE-) - B77-109 (NE-) Always Below 1 Ω
B28-1 (NE) or B77-76 (NE+) - Body ground Always 10 kΩ or higher
B28-2 (NE-) or B77-109 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
B319222
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the crankshaft position sensor installation.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
a.

Inspect the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG