Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.
Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.
The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P0500 | Vehicle Speed Sensor "A" | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (1 trip detection logic). | ·
Open or short in speed signal circuit ·
Combination meter assembly ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
| Related DTCs | P0500: Vehicle speed sensor verify pulse input |
| Required Sensors/Components (Main) | Vehicle speed sensor
Combination meter Skid control ECU |
| Required Sensors/Components (Related) | Park/neutral position switch
Engine coolant temperature sensor Crankshaft position sensor Speed Sensor NC Throttle position sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Duration | 2 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | Off |
| Time after ignition switch off to ON | 3 seconds or more |
| Engine | Running |
| Transaxle counter gear revolution | 300 rpm or higher |
| Lost communication with TCM (U0101) | Not detected |
| Either of the following conditions is met | 1 or 2 |
| 1. All of the following conditions are met | - |
| Engine coolant temperature | 20°C (68°F) or higher |
| Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Not detected |
| Time after park/neutral position switch on to off | 2 seconds or more |
| 2. All of the following conditions are met | - |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature | Less than 20°C (68°F) |
| (b) Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Detected |
| Time after park/neutral position switch on to off | 30 seconds or more |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | Off |
| Time after ignition switch off to ON | 3 seconds or more |
| Engine | Running |
| Transaxle counter gear revolution | 300 rpm or higher |
| Either of the following conditions is met | 1 or 2 |
| 1. All of the following conditions are met | - |
| Engine coolant temperature | 20°C (68°F) or higher |
| Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Not detected |
| Time after park/neutral position switch on to off | 2 seconds or more |
| 2. All of the following conditions are met | - |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature | Less than 20°C (68°F) |
| (b) Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) | Detected |
| Time after park/neutral position switch on to off | 30 seconds or more |
| Vehicle speed sensor signal | No signal |
| Vehicle speed sensor signal | No signal |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine.
Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0500.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
Drive the vehicle.
Read the value displayed on the Techstream.
| Result | Proceed to |
|---|---|
| Values displayed on Techstream and speedometer display not equal | A |
| Values displayed on Techstream and speedometer display equal | B |
A
B
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A62-57 (SPD) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the circuits that send vehicle speed signals to this system in the combination meter system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
If no DTCs (no pending DTCs) are output to the Techstream, the repair has been successfully completed.
| Proceed to |
|---|
| NEXT |
NEXT