Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.12–2013.11
RM30B0U _58 Vehicle Interior _009872 METER / GAUGE / DISPLAY _0058007 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU).

WIRING DIAGRAM

E270458
5.135,3.458 7.156,3.729 2.021,0.271 10 false Combination Meter Assembly 5.125,3.292 5.656,3.49 0.531,0.198 10 false G16 5.594,0.573 6.125,0.771 0.531,0.198 10 false SI 5.594,2.521 6.125,2.719 0.531,0.198 10 false +S 5.354,0.469 5.885,0.667 0.531,0.198 10 false 5 5.365,2.406 5.896,2.604 0.531,0.198 10 false 6 0.427,1.438 3.667,1.719 3.24,0.281 10 false Brake Actuator Assembly (Skid Control ECU) 0.427,1.271 0.958,1.469 0.531,0.198 10 false A64 1.625,0.469 2.156,0.667 0.531,0.198 10 false SP1 2.01,0.458 2.542,0.656 0.531,0.198 10 false 11 0.583,2.906 2.604,3.125 2.021,0.219 10 false Radio Receiver Assembly*1 0.583,3.24 3.396,3.479 2.813,0.24 10 false Radio and Display Receiver Assembly*2 2.063,2.521 2.594,2.719 0.531,0.198 10 false G48 2.385,2.51 2.917,2.708 0.531,0.198 10 false G143 2.115,2.708 2.427,2.885 0.313,0.177 10 false *1 2.49,2.708 2.802,2.885 0.313,0.177 10 false *2 2.104,2.313 2.417,2.49 0.313,0.177 10 false 17 2.479,2.313 2.792,2.49 0.313,0.177 10 false 17 1.656,2.406 2.188,2.604 0.531,0.198 10 false SPD 0.396,5.365 3.24,5.604 2.844,0.24 10 false Stereo Component Amplifier Assembly*3 0.396,5.198 0.927,5.396 0.531,0.198 10 false M22 1.667,4.76 2.198,4.958 0.531,0.198 10 false SPD 2.063,4.76 2.375,4.938 0.313,0.177 10 false 11 0.302,7.5 3.406,7.74 3.104,0.24 10 false Certification ECU (Smart Key ECU Assembly)*4 0.302,7.323 0.833,7.521 0.531,0.198 10 false G84 1.667,6.948 2.198,7.146 0.531,0.198 10 false SPD 2.073,6.948 2.385,7.125 0.313,0.177 10 false 27 6.083,7.354 6.615,7.552 0.531,0.198 10 false A62 6.083,7.51 6.615,7.708 0.531,0.198 10 false ECM 5.729,6.938 6.26,7.135 0.531,0.198 10 false SPD 5.469,6.938 5.781,7.115 0.313,0.177 10 false 57 0.073,8.115 2.302,8.333 2.229,0.219 10 false *1: for Radio Receiver Type 0.083,8.448 2.313,8.667 2.229,0.219 10 false *2: for Radio and Display Type 2.396,8.125 4.625,8.344 2.229,0.219 10 false *3: for 11 Speakers 2.396,8.458 4.625,8.677 2.229,0.219 10 false *4: w/ Smart Key System

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.*

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

*: w/ Smart Key System



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Proceed to
for Radio Receiver Type
for Radio and Display Type



for Radio Receiver Type

2.CHECK RADIO RECEIVER ASSEMBLY

for Radio and Display Type

8.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO RECEIVER ASSEMBLY
E179098
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for 11 Speakers

*2: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.*1


c.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2


d.

Disconnect the A62 ECM connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
NOTICE:

For vehicle except 11 speakers, proceed to next step.


E179098
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G143 radio and display receiver assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the A62 ECM connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicle without a smart key system, proceed to next step.


E179098
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Radio and DisplayType

*3: for 11 Speakers


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G143 radio and display receiver assembly connector.*2


d.

Disconnect the M22 stereo component amplifier assembly connector.*3


e.

Disconnect the A62 ECM connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ECM

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
5.CHECK ECM
E179098
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: for 11 Speakers

*4: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G143 radio and display receiver assembly connector.*2


d.

Disconnect the M22 stereo component amplifier assembly connector.*3


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*4


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
6.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E235636
0.208,0.969 0.563,1.188 0.354,0.219 2.104,0.969 2.271,0.219 2.271,0.219 2.438,0.219 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 0.26,1 0.573,1.198 0.313,0.198 10 false A64 2.479,0.135 3.01,0.333 0.531,0.198 10 false SP1
*a Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU)


a.

Disconnect the A64 brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-11 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
7.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)
E200403
0.177,0.969 0.573,1.188 0.396,0.219 2.708,0.365 2.531,0.365 2.531,0.365 2.219,1.094 false 2.771,0.302 2.938,0.448 0.167,0.146 10 SI 0.24,1.01 0.604,1.198 0.365,0.188 10 G16 1.333,4.094 1.458,4.24 0.125,0.146 10 A 2.969,3.521 3.302,3.667 0.333,0.146 10 GND

a.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G16-5 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G16-5 (SI) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

8.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
E179098
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for 11 Speakers

*2: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.*1


c.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2


d.

Disconnect the A62 ECM connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: for 11 Speakers

*2: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.


c.

Disconnect the M22 stereo component amplifier assembly connector.*1


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2


e.

Disconnect the A62 ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G48-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G48-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G143 radio and display receiver assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the A62 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - M22-11 (SPD) Always Below 1 Ω
G16-6 (+S) or M22-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: for 11 Speakers


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G143 radio and display receiver assembly connector.*2


e.

Disconnect the M22 stereo component amplifier assembly connector.*3


f.

Disconnect the A62 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G84-27 (SPD) Always Below 1 Ω
G16-6 (+S) or G84-27 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: for 11 Speakers

*4: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G143 radio and display receiver assembly connector.*2


e.

Disconnect the M22 stereo component amplifier assembly connector.*3


f.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*4


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-57 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-57 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A64 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-5 (SI) - A64-11 (SP1) Always Below 1 Ω
G16-5 (SI) or A64-11 (SP1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: for 11 Speakers

*2: w/ Smart Key System


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.


c.

Disconnect the M22 stereo component amplifier assembly connector.*1


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2


e.

Disconnect the A62 ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G143-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G143-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR