Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0115.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0115

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0116 Engine Coolant Temperature Circuit Range / Performance Problem When either of the following conditions is met (2 trip detection logic).
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change.


For Mexico Models:
Case 1:
The Engine Coolant Temperature (ECT) is between 35 and 60°C (95 and 140°F) when the engine is started, and both of the following conditions are met (2 trip detection logic)

(a) Vehicle driven at varying speeds (accelerated and decelerated)

(b) Engine coolant temperature remains within 3°C (5.4°F) of initial engine coolant temperature


Case 2:
The ECT is higher than 60°C (140°F) when the engine is started, and both of the following conditions are met (6 trip detection logic)

(a) Vehicle driven at varying speeds (accelerated and decelerated)

(b) Engine coolant temperature measurements remain within 1°C (1.8°F) of initial engine coolant temperature on 6 successive occasions


·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored DTC for Mexico Models
- Applies

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Cold Start Monitor

The monitor runs when the engine is started cold. If the change in engine coolant temperature sensor output until the engine is warmed up completely is less than the threshold, it is determined that a malfunction has occurred in the engine coolant temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


Engine Coolant Temperature Sensor Soak Monitor

The ECM compares the engine coolant temperature when the fully warmed up engine is stopped and when the engine is started on the next trip when more than 5 hours has elapsed since the engine was stopped. If the change in engine coolant temperature sensor output is less than the threshold, it is determined that a malfunction has occurred in the engine coolant temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


Engine Coolant Temperature Sensor High Side Stuck Monitor (Only for Mexico Models)

The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the sensor voltage output deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the engine coolant temperature sensor and stores the DTC.

Examples:

·

Upon starting the engine, the ECT is between 35 and 60°C (95 and 140°F). If, after driving for 250 seconds, the ECT remains within 3°C (5.4°F) of the starting temperature, the DTC is stored (2 trip detection logic).

·

Upon starting the engine, the ECT is higher than 60°C (140°F). If, after driving for 250 seconds, the ECT remains within 1°C (1.8°F) of the starting temperature, the DTC is stored (6 trip detection logic).



MONITOR STRATEGY

Related DTCs P0116: Engine coolant temperature sensor rationality (cold start monitor)
P0116: Engine coolant temperature sensor rationality (soak monitor)
Required Sensors/Components (Main) Engine coolant temperature sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration 10 seconds: Soak monitor
-: Cold start monitor
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None

Cold Start Monitor
All of the following conditions are met -
Battery voltage 10.5 V or higher
Time after engine start 1 second or more
Engine coolant temperature at engine start Less than 60°C (140°F)
Soak time 0 second or more
Accumulated mass air flow 5773 g or more
Fuel cut Off
Intake air temperature sensor circuit fail (P0112, P0113) Not detected
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) Not detected
Thermostat fail (P0128) Not detected
Difference between engine coolant temperature at engine start and intake air temperature Less than 40°C (72°F)

Soak Monitor
All of the following conditions are met -
Battery voltage 10.5 V or higher
Engine Running
Soak time 5 hours or more
Either of the following conditions is met 1 or 2
1. Engine coolant temperature 60°C (140°F) or higher
2. Accumulated mass air flow 11546 g or more
Intake air temperature sensor circuit fail (P0112, P0113) Not detected
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118, P0125) Not detected
Thermostat fail (P0128) Not detected
Soak timer circuit fail (P2610) Not detected

TYPICAL MALFUNCTION THRESHOLDS

Cold Start Monitor
Engine coolant temperature sensor value change Less than 5°C (9°F)

Soak Monitor
Difference between current engine coolant temperature sensor value and previous engine coolant temperature sensor value when engine stopped Less than 5°C (9°F) (Varies with engine coolant temperature of last trip engine stop)

COMPONENT OPERATING RANGE

Engine coolant temperature Engine coolant temperature sensor value changes in accordance with actual engine coolant temperature

CONFIRMATION DRIVING PATTERN

A198823
0.906,1.146 1.427,1.427 0.521,0.281 10 40 km/h 1.063,1.698 1.625,2.031 0.563,0.333 10 Idling 2.74,2.531 3.958,2.781 1.219,0.25 10 5 minutes or more 4.125,0.125 5.833,0.271 1.708,0.146 10 Total of 5 minutes or more 2.073,1.917 2.365,2.156 0.292,0.24 10 [A] 3.25,1.635 3.625,1.917 0.375,0.281 10 [B] 3.99,2.865 4.302,3.125 0.313,0.26 10 [C] 6.156,2.865 6.49,3.125 0.333,0.26 10 [E] 0.5,2 1.406,2.375 0.906,0.375 10 Ignition Switch ON 4.833,0.656 5.167,0.938 0.333,0.281 10 [D] 1.385,3.125 6.708,3.333 5.323,0.208 10 HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for 30 seconds.

7.

Turn the ignition switch to ON and turn the Techstream on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0116.

13.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


15.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.


16.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117, P0118 or P0125 are output simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

Inspect the thermostat (opening temperature).

Click hereEngine / Hybrid System>2AR-FE COOLING>THERMOSTAT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG