Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P050A  Cold Start Idle Air Control System Performance  


MONITOR DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will be stored after the engine idles for 13 seconds (2 trip detection logic).

The DTC is designed to monitor the idle air control at cold start. When the engine is started at an engine coolant temperature of below 50°C (122°F), the ECM measures the accumulated mass air flow during engine idling. If the accumulated mass air flow does not reach the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

The electronic throttle control system controls the idle speed. The electronic throttle control system operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:

The idle speed control learned values are cleared by performing a learned value reset. Idle speed control learning needs to be performed before this DTC can be stored.


HINT:

Idle speed control learning is performed when the engine is warmed up and has been idling for 5 minutes.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


A234891
2.573,2.667 2.229,2.927 false 0.083,0.021 1.885,0.208 1.802,0.188 10 P050A Detection Logic: 1.396,2.865 2.26,3.073 0.865,0.208 10 Engine Start 4.75,1.052 6.354,1.208 1.604,0.156 10 Pass Condition Detected 4.75,2.073 5.542,2.25 0.792,0.177 10 Malfunction 2.115,2.542 2.271,2.719 0.156,0.177 10 0 2.938,2.917 3.635,3.083 0.698,0.167 10 3 seconds 4.604,2.917 5.365,3.083 0.76,0.167 10 13 seconds 4.885,2.594 5.208,2.771 0.323,0.177 10 Time 4.75,1.573 5.438,1.729 0.688,0.156 10 Threshold 1.344,0.76 2.25,1.094 0.906,0.333 10 Accumulate Mass Air Flow 2.208,3.323 4.979,3.49 2.771,0.167 10 Engine Coolant Temperature: -10 to 50°C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050A Cold Start Idle Air Control System Performance Insufficient mass air flow after a cold start (2 trip detection logic).
·

Throttle with motor body assembly

·

Mass air flow meter sub-assembly

·

PCV system

·

Air cleaner filter element

·

Intake system

·

VVT system

·

Wire harness or connector

·

ECM


Comes on DTC stored DTC for Mexico Models
- Not apply

MONITOR STRATEGY

Related DTCs P050A: Cold start idle air speed control system
Required Sensors/Components (Main) Throttle with motor body assembly
Required Sensors/Components (Related) Mass air flow meter sub-assembly
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle
Duration 10 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored P0010 (VVT oil control valve)
P0011 (VVT system - advance)
P0012 (VVT system - retard)
P0016 (VVT system - misalignment)
P0013 (Exhaust VVT oil control valve)
P0014 (Exhaust VVT system - advance)
P0015 (Exhaust VVT system - retard)
P0017 (Exhaust VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172 (Fuel system)
P0301 - P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0365, P0367, P0368 (Exhaust camshaft position sensor)
P0351 - P0354 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air fuel ratio sensor)
P219A (Air fuel ratio imbalance)
Battery voltage 8 V or higher
Time after engine start 3 seconds or more
Starter Off
Engine coolant temperature at engine start -10°C (14°F) or higher
Engine coolant temperature -10°C (14°F) or higher, and less than 50°C (122°F)
Engine idling time 3 seconds or more
Fuel-cut Off
Vehicle speed Less than 3 km/h (1.875 mph)
Time after shift position changed 1 second or more
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher

TYPICAL MALFUNCTION THRESHOLDS

Accumulated mass air flow Less than 25 g (varies with engine coolant temperature and engine coolant temperature at engine start)

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

7.

Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).

8.

Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.

9.

Idle the engine for 1 minute or more [B].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P050A.

14.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C] again.



15.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P050A is output A
DTC P050A and other DTCs are output B


HINT:

If any DTCs other than P050A are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (FUEL TRIM)

B

2.READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter sub-assembly.


a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Gas AF Control / Short FT #1 and Long FT #1.

Powertrain > Engine and ECT > Data List
Tester Display
Short FT #1
Long FT #1
50003 234 25,26

e.

Read the values displayed on the Techstream at engine idle.


f.

Add together the Short FT #1 and Long FT #1 values to obtain the total fuel trim.

Standard:

Total of Short FT #1 and Long FT #1 values is between -20% and 20%.



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

12.CHECK PCV SYSTEM
3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check that there are no deposits around the throttle valve and throttle valve condition.

OK:

No deposits around the throttle valve and throttle valve moves smoothly.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

10.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


k.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


l.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

m.

Input the DTC: P050A.


n.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A is output) B




A

B

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


k.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


l.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

m.

Input the DTC: P050A.


n.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P050A is output) A
NORMAL (DTC is not output) B




A

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

END

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

8.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in step 16 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
HINT:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


k.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


l.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

m.

Input the DTC: P050A.


n.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A is output) B




A

END

B

10.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Repair or replace the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


k.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


l.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

m.

Input the DTC: P050A.


n.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A is output) B




A

END

B

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
12.CHECK PCV SYSTEM
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

PCV valve and hose are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE SYSTEM

NG

20.REPAIR OR REPLACE PCV HOSE
13.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.



Result:
Proceed to
OK
NG



OK

14.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

19.REPAIR OR REPLACE INTAKE SYSTEM
14.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element is not excessively contaminated with dirt or oil.



Result:
Proceed to
OK
NG



OK

15.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

NG

18.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
15.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
a.

Operate the VVT system through the Active Test, and check if the VVT system is operating normally.

i.

Perform the Active Test, referring to DTC P0011 Procedure (VVT system for intake camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0011


ii.

Perform the Active Test, referring to DTC P0014 Procedure (VVT system for exhaust camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0014



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING TECHSTREAM (MAF)

NG

17.CHECK AND REPAIR VVT SYSTEM
16.READ VALUE USING TECHSTREAM (MAF)

OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
17.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.

HINT:
·

Refer to DTC P0011 Procedure for intake camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0011

·

Refer to DTC P0014 Procedure for exhaust camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0014




Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
18.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
19.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
20.REPAIR OR REPLACE PCV HOSE
a.

Repair or replace the PCV valve or hose.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)