Home › Engine / Hybrid System › 2AR-FE LUBRICATION › OIL PUMP
RM30B0U _51 Engine / Hybrid System _009177 2AR-FE LUBRICATION _0050593 OIL PUMP A

2AR-FE LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Do not remove the oil pump or oil pump relief valve from the timing chain cover sub-assembly.


PROCEDURE

Hide 2.DISCONNECT ENGINE WIRE

a.

Disconnect the connectors and clamps securing the engine wire from the engine.


Hide 4.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A195876

Remove the 16 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A196857

Remove the 2 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


c.

Remove the gasket from the No. 2 camshaft bearing cap.


Hide 5.REMOVE SPARK PLUG TUBE GASKET

a.
A195877

Using a screwdriver, pry out the 4 spark plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 8.REMOVE ENGINE MOUNTING BRACKET RH

a.
A195868

Remove the 4 bolts and engine mounting bracket RH.


Hide 9.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 10.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A196847

Remove the 17 bolts and 2 nuts.


b.
A296895
2.594,0.625 2.948,0.219 2.948,0.219 3.083,0.219 true 0.292,3.75 0.969,3.75 true 0.313,1.063 0.5,1.063 0.5,1.063 0.969,0.677 true 2.521,3.813 3.115,3.813 true 0.094,0.979 0.292,1.146 0.198,0.167 10 false *1 3.135,0.125 3.333,0.292 0.198,0.167 10 false *1 3.156,3.729 3.354,3.896 0.198,0.167 10 false *1 0.083,3.667 0.281,3.833 0.198,0.167 10 false *1
*1 Protective Tape


Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and timing chain cover.


HINT:

Tape the screwdriver tip before use.



c.
A196858

Remove the 2 oil pump gaskets from the stiffening crankcase.


d.

Remove the oil hole cover gasket from the stiffening crankcase.


Hide 11.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A302704
0.938,0.313 1.156,0.313 1.156,0.313 1.469,0.792 true 2.146,1.031 2.583,1.458 2.583,1.458 2.771,1.458 true 0.729,0.229 0.927,0.406 0.198,0.177 10 false *1 2.813,1.365 3.01,1.542 0.198,0.177 10 false *2
*1 Protective Tape
*2 Wooden Block


Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.