Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050875 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.REMOVE NO. 1 ENGINE UNDER COVER

a.
A297376

Remove the 2 screws, 4 bolts, 8 clips and No. 1 engine under cover.


Hide 7.REMOVE REAR ENGINE UNDER COVER RH

a.
A297336

Remove the 3 clips and rear engine under cover RH.


Hide 8.REMOVE REAR ENGINE UNDER COVER LH

a.
A296295

Remove the 3 clips and rear engine under cover LH.


Hide 9.REMOVE FRONT FLOOR COVER

Hide 13.DRAIN TRANSFER OIL (for AWD)

Hide 14.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 15.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 16.REMOVE BATTERY INSULATOR

Hide 19.REMOVE FRONT BATTERY BRACKET

Hide 20.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 21.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 22.REMOVE AIR CLEANER CASE

Hide 24.DISCONNECT RADIATOR RESERVOIR ASSEMBLY

Hide 25.REMOVE FAN AND GENERATOR V BELT

Hide 27.DISCONNECT NO. 2 RADIATOR HOSE

Hide 28.REMOVE RADIATOR HOSE HOSE CLAMP

Hide 29.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 30.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 31.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A240912

Remove the No. 1 fuel pipe clamp.


b.

Disconnect the fuel tube connector.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 34.DISCONNECT WIRE HARNESS AND HOSE

a.
A296296

Remove the terminal cap.


b.
A296297

Remove the nut, and disconnect the clamp and starter wire harness.


c.
A296300

Remove the bolt. Then disconnect the 2 clamps and wire harness.


d.
A296298

Remove the nut from the engine room No. 1 relay block.


e.

Disconnect the 2 connectors, detach the 2 claws from the engine room No. 1 relay block and disconnect the wire harness.


f.
A296299

Remove the bolt and disconnect the wire harness.


g.
A296301

Slide the clip and disconnect the vacuum hose from the No. 1 hose to hose tube.


h.
A297337

Slide the clip and disconnect the heater hose from the cylinder head sub-assembly.


i.

Slide the clip and disconnect the heater hose from the No. 1 water by-pass pipe.


Hide 35.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A296889

Remove the nut and disconnect the transmission control cable from the control shaft lever.


b.

Remove the clip and disconnect the transmission control cable from the control cable bracket.


Hide 36.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 37.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 38.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 39.REMOVE FRONT AXLE SHAFT NUT LH

Hide 40.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 41.DISCONNECT FRONT SPEED SENSOR LH

Hide 42.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 44.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 46.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 47.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52.REMOVE DRIVE SHAFT BEARING BRACKET

a.

Remove the 3 bolts and bracket.


Hide 53.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A196625

Remove the flywheel housing under cover.


Hide 54.REMOVE FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

Hide 55.REMOVE FRONT EXHAUST PIPE SUB-ASSEMBLY

Hide 57.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 58.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 59.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Remove the 4 bolts and front suspension member reinforcement RH.


Hide 60.INSTALL ENGINE HANGER

a.
A195856
2.74,0.271 2.896,0.177 2.896,0.177 3.063,0.177 false 1,0.292 1.146,0.177 1.146,0.177 1.281,0.177 false 1.313,0.063 1.51,0.25 0.198,0.188 10 *1 3.104,0.083 3.302,0.271 0.198,0.188 10 *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-36020
No. 2 Engine Hanger 12282-36021
Bolt 91552-81025
91552-81040



Hide 61.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A296304

Remove the 6 bolts and front crossmember sub-assembly.


b.
A296305

Remove the through bolt, nut and front engine mounting insulator.

NOTICE:

While holding the nut in place, loosen the through bolt.



c.

Set an engine lifter underneath the engine.

NOTICE:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.
A296306

Remove the bolt and 2 nuts and disconnect the engine mounting insulator sub-assembly RH.


e.
A296307

Remove the bolt and nut and disconnect the engine mounting insulator LH.


f.
A296308

Remove the 6 bolts and front suspension member rear brace RH and front suspension member rear brace LH.


g.
A296309

Remove the 2 bolts and front suspension crossmember sub-assembly.


h.

Operate the engine lifter and slowly remove the engine from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




i.

Attach an engine sling device and hang the engine with a chain block.


j.
A296310

Remove the through bolt and front suspension crossmember sub-assembly from the engine with transaxle.

NOTICE:

Do not damage any engine or transaxle components.


HINT:

Raise the engine with transaxle assembly while keeping it level.



Hide 62.REMOVE STARTER ASSEMBLY

Hide 63.REMOVE TRANSFER ASSEMBLY (for AWD)

Hide 65.FIX ENGINE ASSEMBLY

a.

Using wooden blocks or plate lift attachments, set the engine on a flat surface.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine is level.

·

Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.

·

Perform this step while supporting the engine assembly using a sling device and chain block.




Hide 66.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 67.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 68.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Install the engine to an engine stand with the bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 69.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:
A296311

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.

Remove the 2 bolts, 2 nuts and rear engine mounting insulator.


Hide 70.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:
A296312

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.

Remove the bolt and radiator reservoir bracket.


b.

Remove the 3 bolts and engine mounting insulator sub-assembly RH.


Hide 71.REMOVE ENGINE MOUNTING SPACER

HINT:
A296313

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.

Remove the 2 bolts and engine mounting spacer.


Hide 72.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:
A296314

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Remove the bolt and wire harness clamp bracket.


b.

Remove the 4 bolts and engine mounting insulator LH.