Initialization is necessary if one of the following occurs:
The tire pressure warning ECU and receiver is replaced.
A tire pressure warning valve and transmitter is replaced.
Tires with a different tire standard pressure are installed.
The tires are rotated.
A new vehicle is delivered.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C2177/77 | Initialization not Completed | All conditions below are met:
·
During initialization ·
Tire pressure warning valve and transmitter is not in stop mode ·
Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more ·
Vehicle speed is more than 37 km/h (23 mph) for a total of 20 minutes |
·
Tire pressure warning valve and transmitter ·
Wire harness or connector ·
Tire pressure warning ECU and receiver |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.
Check that the vehicle is not located in an area such as described below:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on after blinking 1 minute only in a particular area due to interfering radio frequencies.
Devices using similar radio frequencies are used in the vehicle.
Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
Radio transmissions may be interrupted due to the surroundings, or devices installed by the user.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi) |
Actual tire inflation pressure | ·
If N/A is displayed, data has not been received.* ·
w/ Full Size Spare Tire |
*: It may take a few minutes until the values are displayed.
When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.
| Tester Display |
|---|
| ID 1 Tire Inflation Pressure |
| ID 2 Tire Inflation Pressure |
| ID 3 Tire Inflation Pressure |
| ID 4 Tire Inflation Pressure |
| ID 5 Tire Inflation Pressure |
| Proceed to |
|---|
| All tire pressure readings are equal to specified values. |
| Tire pressure values are not displayed. |
All tire pressure readings are equal to specified values.
Tire pressure values are not displayed.