Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM30B0U _53 Suspension _009252 TIRE PRESSURE MONITORING _0050645 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the wheels are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

Initialization is normally completed within a few minutes.

·

It may take up to a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21

·

If initialization has not been completed successfully, DTC C2177/77 is stored after a vehicle speed of 37 km/h (23 mph) or more continues for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·
C217594
1.802,1.427 2.052,1.76 false 1.76,0.292 1.604,0.896 false 0.156,0.083 0.833,0.365 0.677,0.281 10 *a 1.969,1.792 2.49,1.969 0.521,0.177 10 TC 1.688,0.125 2.042,0.302 0.354,0.177 10 CG
*a Front view of DLC3


Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



BEFORE INITIALIZATION


a.

Make sure that the tires are cold.


b.

Set the air pressure of all tires to the specified value(s).

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION



INITIALIZATION PROCEDURE


a.

Turn the ignition switch to ON.


b.
C279776
1.208,0.49 1.521,0.688 0.313,0.198 10 *1 3.01,2.76 3.323,2.958 0.313,0.198 10 *2 0.208,3.188 0.521,3.385 0.313,0.198 10 *a 1.292,2.938 1.604,3.135 0.313,0.198 10 *b 1.063,4.188 1.375,4.385 0.313,0.198 10 *b 0.323,3.417 0.635,3.615 0.313,0.198 10 *c 0.313,3.688 0.625,3.885 0.313,0.198 10 *d
*1 Tire Pressure Warning Light
*2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.


c.

Turn the ignition switch off.


d.

Connect the Techstream to the DLC3.


e.

Turn the ignition switch to ON and turn the Techstream on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the Techstream screen.