The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.
Click hereEngine / Hybrid System>2AR-FE STARTING>STARTING SYSTEM>PRECAUTION
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
3.INSPECT BATTERY
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner cap.
Remove the air cleaner filter element sub-assembly.
Visually check that the air cleaner filter is not excessively damaged or oily.
If necessary, replace the air cleaner filter element sub-assembly.
5.INSPECT SPARK PLUG
6.INSPECT FAN AND GENERATOR V BELT
7.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.
If any defects or problems are found during the inspection above, perform a lash adjuster inspection.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION
8.INSPECT IGNITION TIMING
Warm up and stop the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Start the engine and idle it.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.
5 to 15° BTDC @ idle
| Tester Display |
|---|
| IGN Advance |
Refer to the Techstream operator's manual for further details.
If the ignition timing is not as specified, check the valve timing.
When not using the Techstream:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Use a timing light that detects primary signals.
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
When checking the ignition timing, the transaxle should be in neutral.
Using a timing light, check the ignition timing.
8 to 12° BTDC @ idle
Remove SST from the DLC3.
Check the ignition timing.
5 to 15° BTDC @ idle
If the ignition timing is not as specified, check the valve timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Disconnect the timing light from the engine.
9.INSPECT ENGINE IDLE SPEED
Warm up and stop the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Switch off all accessories and the A/C before connecting the Techstream.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
720 to 820 rpm
When checking the idle speed, the transaxle should be in neutral.
Refer to the Techstream operator's manual for further details.
If the idle speed is not as specified, check the air intake system.
Disconnect the Techstream from the DLC3.
When not using the Techstream:
| *a | Front view of DLC3 |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
Confirm the terminal number before connecting the probe. Connecting the wrong terminals can damage the engine.
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
720 to 820 rpm
If the speed is not as specified, check the air intake system.
Disconnect the tachometer probe from the DLC3.
10.INSPECT COMPRESSION
Warm up and stop the engine.
Check for DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Remove the 4 spark plugs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 4 fuel injector connectors.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
1450 kPa (14.8 kgf/cm2, 210 psi) or higher
980 kPa (10.0 kgf/cm2, 142 psi)
200 kPa (2.0 kgf/cm2, 29 psi) or less
Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.
If adding oil helps boost the compression, it is likely that the piston rings and/or cylinder bore is worn or damaged.
If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
11.INSPECT CO/HC
This check determines whether or not the idle CO/HC complies with regulations.
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check the CO/HC concentration at idle and at 2500 rpm.
When performing the 2-mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.
If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.
Check the air fuel ratio sensor operation.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION
Check the heated oxygen sensor operation.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Causes |
|---|---|---|---|
| Normal | High | Rough idle | 1. Faulty ignition ·
Incorrect timing ·
Plugs are contaminated or shorted, or gaps are defective 2. Leaky intake and exhaust valves 3. Leaky cylinder |
| Low | High | Rough idle
(Fluctuating HC reading) |
1. Vacuum leaks ·
PCV hose ·
Intake manifold ·
Throttle body ·
Brake booster line 2. Lean mixture causing misfire |
| High | High | Rough idle
(Black smoke from exhaust) |
1. Restricted air filter 2. Faulty SFI system ·
Faulty pressure ·
Defective engine coolant temperature sensor ·
Faulty ECM ·
Faulty injector ·
Faulty throttle position sensor ·
Faulty mass air flow meter sensor |