Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside spiral with sensor cable sub-assembly (steering angle sensor)

·

Spiral with sensor cable sub-assembly (steering angle sensor) CAN branch wire or connector

·

Spiral with sensor cable sub-assembly (steering angle sensor)



WIRING DIAGRAM

C280376
0.135,1.823 2.177,2.167 2.042,0.344 10 false G122*1 0.125,1.99 2.167,2.333 2.042,0.344 10 false No. 1 CAN Junction Connector*1 0.25,4.906 2.292,5.25 2.042,0.344 10 false *1: for 2 Pin Connector Type 0.229,5.25 2.271,5.594 2.042,0.344 10 false *2: for 22 Pin Connector Type 1.74,3.479 3.781,3.823 2.042,0.344 10 false from IG1 NO.1 Relay 2.24,2.646 4.281,2.99 2.042,0.344 10 false from Battery 3.99,2.479 5.042,2.885 1.052,0.406 10 false ECU-B NO.1 4,3.292 5.052,3.698 1.052,0.406 10 false ECU-IG NO.1 1.708,1.344 3.75,1.688 2.042,0.344 10 false 2*1, 14*2 1.698,0.771 3.74,1.115 2.042,0.344 10 false 1*1, 3*2 5.677,0.885 6.604,1.26 0.927,0.375 10 false CANH 5.688,1.448 6.615,1.823 0.927,0.375 10 false CANL 5.688,2.635 6.615,3.01 0.927,0.375 10 false BAT 5.698,3.448 6.625,3.823 0.927,0.375 10 false IG 5.677,4.115 6.604,4.49 0.927,0.375 10 false ESS 5.427,4 6.354,4.385 0.927,0.385 11 false 1 5.427,3.344 6.354,3.729 0.927,0.385 11 false 4 5.438,2.51 6.365,2.896 0.927,0.385 11 false 5 5.427,1.323 6.354,1.708 0.927,0.385 11 false 2 5.438,0.729 6.365,1.115 0.927,0.385 11 false 3 4.656,4.948 5.583,5.323 0.927,0.375 10 false G12 4.656,5.104 7.073,5.469 2.417,0.365 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 0.146,2.438 2.188,2.781 2.042,0.344 10 false No. 4 CAN Junction Connector*2 0.135,2.281 2.177,2.625 2.042,0.344 10 false G134*2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
C277459
0.354,1.115 0.771,1.365 0.417,0.25 1.083,1.833 1.333,1.833 1.333,1.833 1.51,1.385 true 2.167,1.833 1.917,1.833 1.917,1.833 1.677,1.385 true 0.083,0.052 0.396,0.208 0.313,0.156 10 *a 2.198,1.75 2.677,1.906 0.479,0.156 10 CANH 0.656,1.75 1.135,1.906 0.479,0.156 10 CANL 0.417,1.167 0.896,1.323 0.479,0.156 10 G12
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
C277459
0.354,1.115 0.771,1.365 0.417,0.25 0.917,1.833 1.167,1.833 1.167,1.833 1.344,1.385 true 2.573,1.833 2.323,1.833 2.323,1.833 2.083,1.385 true 2.563,0.781 2.313,0.781 2.313,0.781 1.917,1.229 true 0.083,0.052 0.396,0.208 0.313,0.156 10 *a 2.625,1.75 3.104,1.906 0.479,0.156 10 BAT 0.583,1.75 1.063,1.906 0.479,0.156 10 ESS 0.417,1.167 0.896,1.323 0.479,0.156 10 G12 2.594,0.688 3.073,0.844 0.479,0.156 10 IG
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G12-5 (BAT) - Body ground Always 11 to 14 V
G12-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-1 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR