Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside ECM

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

C280377
5.563,0.573 6.177,0.771 0.615,0.198 10 false CANH 5.563,1.417 6.177,1.615 0.615,0.198 10 false CANL 1.5,1.188 2.438,1.427 0.938,0.24 10 false 2*1, 13*2 1.5,0.573 2.438,0.813 0.938,0.24 10 false 1*1, 2*2 0.042,1.667 0.979,1.906 0.938,0.24 10 false N27*1 0.042,1.833 2.135,2.167 2.094,0.333 10 false No. 3 CAN Junction Connector*1 2.156,2.458 3.094,2.698 0.938,0.24 10 false from Battery 1.208,3.021 3.167,3.26 1.958,0.24 10 false from EFI-MAIN NO.1 Relay 1.938,4.125 3.115,4.354 1.177,0.229 10 false from IG2 Relay 5.146,1.313 5.5,1.656 0.354,0.344 10 false A62 5.146,0.698 5.5,1.042 0.354,0.344 10 false A62 5.156,2.469 5.51,2.813 0.354,0.344 10 false A62 5.146,3.021 5.5,3.365 0.354,0.344 10 false A62 5.146,3.583 5.5,3.927 0.354,0.344 10 false A62 5.156,4.125 5.51,4.469 0.354,0.344 10 false A62 5.156,4.688 5.51,5.031 0.354,0.344 10 false B77 5.167,5.24 5.521,5.583 0.354,0.344 10 false B77 5.156,5.792 5.51,6.135 0.354,0.344 10 false B77 5.156,6.281 5.51,6.625 0.354,0.344 10 false B77 5.75,7.104 6.188,7.438 0.438,0.333 10 false ECM 5.615,6.292 6.219,6.625 0.604,0.333 10 false ME01 5.594,5.813 6.198,6.146 0.604,0.333 10 false E01 5.594,5.271 6.198,5.604 0.604,0.333 10 false E02 5.594,4.688 6.198,5.021 0.604,0.333 10 false E1 5.583,4.083 6.188,4.417 0.604,0.333 10 false IGSW 5.604,3.583 6.208,3.917 0.604,0.333 10 false +B2 5.604,3.031 6.208,3.365 0.604,0.333 10 false +B 5.594,2.448 6.198,2.781 0.604,0.333 10 false BATT 3.76,2.292 5.24,2.531 1.479,0.24 10 false EFI-MAIN NO.1 4.083,3.969 5.563,4.208 1.479,0.24 10 false IGN 5.219,3.333 6.698,3.573 1.479,0.24 10 false 3 5.229,2.792 6.708,3.031 1.479,0.24 10 false 2 5.229,2.229 6.708,2.469 1.479,0.24 10 false 1 5.188,3.896 6.667,4.135 1.479,0.24 10 false 37 5.188,1.063 6.667,1.302 1.479,0.24 10 false 26 5.198,0.458 6.677,0.698 1.479,0.24 10 false 13 5.198,4.458 6.677,4.698 1.479,0.24 10 false 16 5.208,5 6.688,5.24 1.479,0.24 10 false 49 5.198,5.563 6.677,5.802 1.479,0.24 10 false 50 5.198,6.042 6.677,6.281 1.479,0.24 10 false 58 0.406,6.938 4.688,7.135 4.281,0.198 10 false *1: for 2 Pin Connector Type 0.417,7.302 4.698,7.5 4.281,0.198 10 false *2: for 22 Pin Connector Type 0.052,2.292 2.146,2.625 2.094,0.333 10 false No. 21 CAN Junction Connector*2 0.052,2.146 0.99,2.385 0.938,0.24 10 false A72*2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Drive the vehicle for 50 seconds at a speed of 20 km/h (12 mph).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C228681
0.125,0.979 0.531,1.26 0.406,0.281 2.531,0.938 2.719,0.688 2.719,0.688 2.833,0.688 true 2.531,1.01 2.76,1.156 2.76,1.156 2.875,1.156 true 0.198,1.042 0.698,1.323 0.5,0.281 10 A62 2.875,0.594 3.385,0.854 0.51,0.26 10 CANH 0.104,0.073 0.417,0.229 0.313,0.156 10 *a 2.927,1.063 3.375,1.375 0.448,0.313 10 CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Connector Specified Condition
A62-13 (CANH) - A62-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C229008
1.656,0.51 2.073,0.76 0.417,0.25 5.094,0.542 5.51,0.792 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 1.552,1.375 1.167,0.667 1.167,0.667 0.917,0.667 true 1.667,1.375 1.333,0.417 1.333,0.417 1,0.417 true 1.833,1.615 1.333,2.25 1.333,2.25 1.083,2.25 true 4.844,1.406 4.417,0.75 4.417,0.75 4.167,0.75 true 5.104,1.49 4.75,0.5 4.75,0.5 4.5,0.5 true 5.177,1.521 4.75,2.25 4.75,2.25 4.5,2.25 true 5.865,1.5 6.25,2.25 6.25,2.25 6.5,2.25 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.844 0.75,1.083 0.406,0.24 10 BATT 0.667,0.583 1.073,0.823 0.406,0.24 10 +B 0.677,0.344 1.083,0.583 0.406,0.24 10 +B2 0.667,2.167 1.167,2.417 0.5,0.25 10 IGSW 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 3.917,0.667 4.323,0.906 0.406,0.24 10 E1 4.177,0.427 4.583,0.667 0.406,0.24 10 E02 4.177,2.177 4.583,2.417 0.406,0.24 10 E01 6.583,2.177 6.99,2.417 0.406,0.24 10 ME01 5.177,0.583 5.583,0.823 0.406,0.24 10 B77
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (BATT) - Body ground Always 11 to 14 V
A62-2 (+B) - Body ground Ignition switch ON 11 to 14 V
A62-3 (+B2) - Body ground Ignition switch ON 11 to 14 V
A62-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-16 (E1) - Body ground Always Below 1 Ω
B77-49 (E02) - Body ground Always Below 1 Ω
B77-50 (E01) - Body ground Always Below 1 Ω
B77-58 (ME01) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR