Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Lane Departure Warning Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Lane Departure Warning Camera Communication Stop Mode Either condition is met:
·

"Front Camera Module" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Lane Departure Warning Camera Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside lane departure warning camera

·

Lane departure warning camera CAN branch wire or connector

·

Lane departure warning camera



For vehicles with a lane departure alert system.


WIRING DIAGRAM

C250958
5.625,0.885 6.5,1.25 0.875,0.365 10 CA1P 5.625,1.469 6.125,1.729 0.5,0.26 10 CA1N 5.625,2.49 5.979,2.729 0.354,0.24 10 IGB 5.625,3.083 6.063,3.281 0.438,0.198 10 GND 5.375,0.771 5.625,0.938 0.25,0.167 10 6 5.313,1.344 5.583,1.51 0.271,0.167 10 12 1.667,0.781 1.917,1.01 0.25,0.229 10 1 1.677,1.365 1.896,1.573 0.219,0.208 10 2 5.396,2.365 5.719,2.677 0.323,0.313 10 7 5.333,2.979 5.75,3.24 0.417,0.26 10 11 0.417,1.813 0.927,2 0.51,0.188 10 G125 0.427,1.969 3.167,2.25 2.74,0.281 10 No. 1 CAN Junction Connector 1.677,2.479 3.094,2.729 1.417,0.25 10 from IG1 NO.1 Relay 3.792,2.323 4.875,2.625 1.083,0.302 10 ECU-IG NO.2 5.042,4.01 5.927,4.302 0.885,0.292 10 Q13 5.052,4.177 7.094,4.448 2.042,0.271 10 Lane Departure Warning Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 51 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (LANE DEPARTURE WARNING CAMERA CAN BRANCH WIRE)
a.
C268302
0.333,1.208 0.771,1.448 0.438,0.24 2.063,1.229 2.302,0.854 2.302,0.854 2.5,0.854 true 2.083,1.521 2.271,1.802 2.271,1.802 2.469,1.802 true 0.052,0.042 0.365,0.198 0.313,0.156 10 *a 0.406,1.24 0.719,1.396 0.313,0.156 10 Q13 2.521,1.719 3.021,1.896 0.5,0.177 10 CA1N 2.521,0.771 3.021,0.948 0.5,0.177 10 CA1P
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the lane departure warning camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-6 (CA1P) - Q13-12 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE LANE DEPARTURE WARNING CAMERA CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

2.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - BATTERY AND BODY GROUND)
a.
C268302
0.333,1.208 0.771,1.448 0.438,0.24 1.958,1.5 2.146,1.781 2.146,1.781 2.344,1.781 true 0.958,1.792 1.135,1.792 1.135,1.792 1.354,1.5 true 0.052,0.042 0.365,0.198 0.313,0.156 10 *a 0.417,1.25 0.833,1.458 0.417,0.208 10 Q13 2.385,1.698 2.885,1.875 0.5,0.177 10 GND 0.677,1.708 1.177,1.885 0.5,0.177 10 IGB
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q13-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-11 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR