Home › Suspension › REAR SUSPENSION › REAR LOWER ARM
RM30B0U _53 Suspension _009475 REAR SUSPENSION _0051211 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

Hide 3.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C226957

Remove the nut from the axle carrier.


b.
C229149
0.406,0.125 1.385,0.125 true 1.385,0.125 1.385,0.521 true 1.292,0.521 1.292,0.125 true 2.042,1.292 1.729,1.292 false 1.729,1.365 1.729,1.292 false 1.844,1.365 1.844,1.292 false 0.115,0.052 0.438,0.24 0.323,0.188 10 SST 2.104,1.219 2.427,1.406 0.323,0.188 10 SST 1.625,1.917 1.938,2.073 0.313,0.156 10 *a
*a 1 mm (0.0394 in.)


Install SST to the rear No. 1 suspension arm as shown in the illustration.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the clearance measurement between SST and the rear axle assembly is 1 mm (0.0394 in.).


HINT:

Use 2 SST of the same type.



c.

Using SST, disconnect the rear No. 1 suspension arm from the rear axle carrier as shown in the illustration.

SST
09960-20010  (09961-02010)

C229548
1.677,0.927 0.74,0.927 true 4.49,0.75 3.979,0.75 false 4.49,0.823 4.292,0.823 4.292,0.823 4.292,0.75 false 2.396,1.417 2.625,1.417 false 5.813,2.156 5.552,2.156 false 6.688,0.594 6.833,0.74 0.146,0.146 10 A 6.688,1.25 6.833,1.396 0.146,0.146 10 B 0.583,0.854 0.76,1.01 0.177,0.156 10 *a 3.677,0.688 3.969,0.854 0.292,0.167 10 SST 2.656,1.344 2.948,1.51 0.292,0.167 10 SST 5.396,2.073 5.573,2.229 0.177,0.156 10 *b
*a Tie the string so there is no slack *b Place the wrench here
V100135

Turn
V100136

Molybdenum grease


CAUTION:

Apply molybdenum grease to the threads and end of SST bolt.


NOTICE:
·

Install SST so that A and B are parallel.

·

Be sure to turn the part indicated in the illustration with a wrench.

·

Do not damage the front lower ball joint dust cover.

·

Be sure to tie the string of SST to the vehicle to prevent SST from dropping.




d.
C229151
0.698,0.729 0.698,0.458 true 0.698,0.458 2.719,0.458 true 2.719,0.469 2.719,0.677 true 1.854,0.458 1.854,0.25 false 1.74,0.063 1.938,0.26 0.198,0.198 10 *a
*a Matchmark


Put matchmarks on the rear suspension toe adjust cam, No. 2 camber adjust cam and rear suspension member.


e.
C226958

Remove the nut, No. 2 camber adjust cam, rear suspension toe adjust cam and rear No. 1 suspension arm assembly LH.


Hide 4.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 5.LOOSEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C266840

a.

Loosen the 2 bolts of the rear No. 2 suspension arm.

NOTICE:
·

Do not remove the bolts and nuts, only loosen them.

·

Since a stopper nut is used, loosen the bolt.




Hide 6.REMOVE REAR COIL SPRING LH

a.
C129671

Support the No. 2 suspension arm LH with a jack.

NOTICE:

Place a wooden or rubber block between the jack and arm.



b.
C129668

Remove the bolt located on the rear axle carrier of the rear No. 2 suspension arm.


c.

Lower the jack gradually to remove the rear coil spring together with the rear upper coil spring insulator.


Hide 7.REMOVE REAR UPPER COIL SPRING INSULATOR LH

a.

Remove the rear upper coil spring insulator from the rear coil spring.


Hide 8.REMOVE REAR LOWER COIL SPRING INSULATOR LH

a.

Remove the rear lower coil spring insulator from the rear No. 2 suspension arm.


Hide 9.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C129667

a.

Remove the bolt, nut and rear No. 2 suspension arm from the suspension member.

NOTICE:

Since a stopper nut is used, loosen the bolt.