Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR
RM30B0U _53 Suspension _009475 REAR SUSPENSION _0051213 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR STABILIZER BUSHING

C278709
1.938,0.875 2.104,0.427 false 2.104,0.427 2.229,0.427 false 2.25,0.344 2.563,0.5 0.313,0.156 10 *a
*a Bushing Stopper
V100135

Vehicle Inside


a.

Install the 2 rear stabilizer bushings to the rear stabilizer bar on the outside of the bush stoppers as shown in the illustration.


Hide 2.INSTALL REAR STABILIZER BAR

a.

Install the rear stabilizer bar and rear No. 1 stabilizer bracket LH and RH to the rear suspension member with the 4 bolts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


Hide 3.INSTALL REAR UPPER COIL SPRING INSULATOR LH

C276119
2.969,0.406 3.219,0.594 0.25,0.188 10 *a
*a 10 mm or less


a.

Install the rear upper coil spring insulator to the rear coil spring.

NOTICE:

Install the rear upper coil insulator so that the distance between the stopper and upper end of the rear coil spring is 10 mm (0.394 in.) or less.



Hide 4.INSTALL REAR LOWER COIL SPRING INSULATOR LH

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm.


Hide 5.INSTALL REAR COIL SPRING LH

a.
C266194
0.199,2.302 0.466,2.527 0.267,0.225 10 *a 1.354,1.775 0.421,2.386 false 0.421,2.386 1.355,3.148 false
*a Identification Mark


Install the rear coil spring to the rear No. 2 suspension arm.

NOTICE:

Install the rear coil spring so that the identification marks are positioned as shown in the illustration.



b.
C267389

Using a jack and wooden block, raise the vehicle gradually to install the rear No. 2 suspension arm to the rear axle carrier. Then temporarily install the bolt and nut.


Hide 6.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 7.INSTALL REAR STABILIZER LINK ASSEMBLY LH

NOTICE:

Since the rear stabilizer link, rear stabilizer cushions and nut (B) are not reusable, new parts must be installed.


a.
C211882
0.198,0.406 0.354,0.604 0.156,0.198 10 false .
V100135

Nut (A)
V100136

Nut (B)


Install a new rear stabilizer link assembly LH and 2 new rear stabilizer cushions to the rear No. 2 suspension arm assembly with a new nut (B) as shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Be sure to install the rear stabilizer cushions in the correct direction as shown in the illustration.



b.

Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut (A).

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



c.
C211884
1.292,0.917 1.448,1.115 0.156,0.198 10 A 1.313,1.281 1.469,1.479 0.156,0.198 10 B

Adjust the rear stabilizer link assembly LH so that A and B are parallel as shown in the illustration.


Hide 8.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 10.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C266199

Tighten the 2 bolts of the suspension arm.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 11.INSTALL REAR SUSPENSION MEMBER BRACE LH

a.

Install the rear suspension member brace to the rear suspension member with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 12.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 13.INSPECT AND ADJUST REAR WHEEL ALIGNMENT