Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT
RM30B0U _53 Suspension _009474 ALIGNMENT / HANDLING DIAGNOSIS _0051216 REAR WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  ADJUSTMENT  


PROCEDURE

Hide 3.INSPECT TOE-IN

a.
C260042
0.559,0 0.710,0.194 0.151,0.194 10 A 2.794,0 2.945,0.194 0.151,0.194 10 B 1.706,1.789 1.857,1.983 0.151,0.194 10 C 1.678,0.214 1.829,0.408 0.151,0.194 10 D
V100135

Front of the Vehicle


Bounce the vehicle up and down at the corners to stabilize the suspension and inspect toe-in.

Toe-in (Unloaded Vehicle):
- Front A + B
Rear C - D
Toe-in
(Total)
A + B: 0°11' +/-10' (0.18° +/-0.17°)
C - D: 2.3 +/-1 mm (0.09 +/-0.04 in.)


HINT:

If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.



Hide 4.ADJUST TOE-IN

C226958

a.

Loosen the toe adjust cam nut.


b.
C226959

Turn the adjust cams by an equal amount to adjust the toe-in.

Toe-in (Unloaded Vehicle):
- Front A + B
Rear C - D
Toe-in
(Total)
A + B: 0°11' +/-10' (0.18° +/-0.17°)
C - D: 2.3 +/-1 mm (0.09 +/-0.04 in.)


HINT:
·

Try to adjust the toe-in to the center value.

·

The toe-in will change by approximately 3.6 mm (0.142 in.) for each gradation of the cam.




c.
C226958

Tighten the toe adjust cam nut.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 5.INSPECT CAMBER

C107736
2.031,1.26 2.146,0.771 2.146,0.771 2.25,0.771 false 2.313,0.698 2.625,0.854 0.313,0.156 10 *a
*a Gauge


a.

Install a camber-caster-kingpin gauge or set the vehicle on a wheel alignment tester.


b.

Inspect the camber.

Standard Camber Inclination (Unloaded Vehicle):
Item Tire Size Camber Inclination Right-left Difference
2WD 225/65R17 -1°17' +/-45' (-1.28° +/-0.75°) 45' (0.75°) or less
235/55R18 -1°15' +/-45' (-1.25° +/-0.75°) 45' (0.75°) or less
AWD 225/65R17 -1°17' +/-45' (-1.28° +/-0.75°) 45' (0.75°) or less
235/55R18 -1°16' +/-45' (-1.27° +/-0.75°) 45' (0.75°) or less


If the measured value is not within the specified range, inspect the suspension parts for damage and wear. Replace parts as necessary as the camber cannot be properly adjusted with any damaged or worn parts.



Hide 6.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 7. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

Hide 8.ADJUST LANE DEPARTURE WARNING CAMERA (w/ LANE DEPARTURE WARNING CAMERA)