Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat)
RM30B0U _58 Vehicle Interior _009409 SEAT _0051049 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY LH

a.

Place the front seat assembly LH in the cabin.

NOTICE:
·

Before placing the seat in the vehicle, operate the seat track adjusting handle to slide the seat track to the center position.


·

Be careful not to damage the vehicle body.




b.
B341333

for Driver Side:

i.

Attach the clamp and connect the connector of the front seat inner belt assembly LH.


ii.

Connect the connector of the front seat airbag assembly LH.



c.
B341334
1.896,1.219 2,1.604 true 1.958,1.625 2.271,1.781 0.313,0.156 10 false *A
*A w/ Seat Heater System


for Front Passenger Side:

i.

Attach the clamp and connect the connector of the front seat inner belt assembly RH.


ii.

w/ Seat Heater System:

Disconnect the connector of the seat heater.


iii.

Connect the connector of the front seat airbag assembly RH and connector of the front seat airbag sub-assembly RH.



d.

Temporarily install the front seat assembly with the 4 bolts.


e.

Operate the seat track adjusting handle to move the seat to the rearmost position.


f.
B338226

Tighten the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


g.

Operate the seat track adjusting handle to move the seat to the foremost position.


h.
B338225

Tighten the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


i.

During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the seat mounting bolts to adjust the adjuster position.


Hide 2.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

a.
B339922
1.698,0.656 1.729,0.719 false
V100135

First
V100136

Second


Attach the 2 claws to install the rear outer seat track bracket cover LH as indicated by the arrows in the order shown in the illustration.


Hide 3.INSTALL REAR INNER SEAT TRACK BRACKET COVER LH

a.
B339923
1.521,0.458 1.615,0.552 false
V100135

First
V100136

Second


Attach the 2 claws to install the rear inner seat track bracket cover LH as indicated by the arrows in the order shown in the illustration.


Hide 4.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the seat track adjusting handle to move the seat to the rearmost position.


b.
B339924
1.542,0.552 1.469,0.667 false
V100135

First
V100136

Second


Attach the 2 claws to install the front outer seat track bracket cover LH as indicated by the arrows in the order shown in the illustration.


Hide 5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH

a.
B339925
1.708,0.677 1.583,0.76 false 1.688,0.698 1.563,0.781 false
V100135

First
V100136

Second


Attach the 2 claws to install the front inner seat track bracket cover LH as indicated by the arrows in the order shown in the illustration.


Hide 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly.


Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 9.INSPECT SEAT HEATER SYSTEM