Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for AWD)
RM30B0U _52 Drivetrain _009984 DRIVE SHAFT / PROPELLER SHAFT _0054769 FRONT DRIVE SHAFT ASSEMBLY(for AWD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for AWD)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL FRONT DRIVE SHAFT BEARING

a.
C278916
0.458,1.875 0.958,1.875 0.958,1.875 1.115,1.656 true 0.479,0.313 0.75,0.313 0.75,0.313 0.885,0.563 true 0.167,0.24 0.625,0.438 0.458,0.198 10 SST 0.156,1.771 0.615,1.969 0.458,0.198 10 SST

Using SST and a press, install a new front driveshaft bearing to the front drive inboard joint assembly RH.

SST
09527-10011  
09710-30012  (09710-04081)

NOTICE:

Make sure the bearing is completely installed.



b.
C127665

Using a snap ring expander, install a new snap ring.


Hide 2.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
C127677
0.656,0.656 0.552,0.313 0.552,0.313 0.427,0.313 true 0.094,0.219 0.385,0.375 0.292,0.156 10 SST

Using SST and a press, install a new front drive shaft dust cover LH.

SST
09527-10011  

NOTICE:
·

The front drive shaft dust cover LH should be installed completely.

·

Be careful not to damage the front drive shaft dust cover LH.




Hide 3.INSTALL FRONT DRIVE SHAFT DUST COVER RH

a.

for TMMC Made:

i.
C284195
0.51,0.813 0.51,0.365 0.51,0.365 0.365,0.365 true 1.635,4.063 2.094,4.26 0.458,0.198 10 false (A) 0.073,0.281 0.531,0.479 0.458,0.198 10 false SST

Using SST and a press, install a new front drive shaft dust cover RH to the front drive inboard joint assembly RH as shown in the illustration.

SST
09527-10011  

Standard Distance (A):

87.7 to 88.3 mm (3.453 to 3.476 in.)


NOTICE:

Be careful not to damage the front drive shaft dust cover RH.




b.

except TMMC Made:

i.
C166793
0.5,0.917 0.5,0.583 0.5,0.583 0.365,0.583 true 0.063,0.51 0.521,0.708 0.458,0.198 10 SST 1.76,4.104 2.219,4.302 0.458,0.198 10 (A)

Using SST and a press, install a new front drive shaft dust cover RH to the front drive inboard joint assembly RH as shown in the illustration.

SST
09527-10011  

Standard Distance (A):

103.5 to 104.5 mm (4.075 to 4.114 in.)


NOTICE:

Be careful not to damage the front drive shaft dust cover RH.




Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C127681
2.094,0.479 1.896,0.479 1.896,0.479 1.76,0.75 false 2.146,0.406 2.833,0.573 0.688,0.167 10 false *a
*a Protective Tape


Before installing the front axle outboard joint boot, wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the front axle outboard joint boot from being damaged.


b.

Install new parts to the front drive outboard joint shaft assembly in the following order.

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Install the front axle outboard joint boot so that it is between the front No. 2 axle outboard joint boot clamp and front drive outboard joint shaft assembly.


d.

Temporarily install the front axle outboard joint boot clamp to the front axle outboard joint boot.


e.

Pack the front drive outboard joint shaft assembly and front axle outboard joint boot with grease from the boot kit.

Standard Grease Capacity:
for TMMC Made:

100 to 120 g (3.6 to 4.2 oz)

except TMMC Made:

205 to 215 g (7.3 to 7.5 oz)



Hide 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

for TMMC Made:

i.

Install the front No. 2 axle outboard joint boot clamp LH onto the outboard joint boot.


ii.
C106164
0.906,0.469 1.135,0.469 1.135,0.469 1.5,1.073 true 2.719,0.635 3.031,0.833 0.313,0.198 10 false *a 1.49,0.573 1.802,0.771 0.313,0.198 10 false *b 0.542,0.375 0.854,0.573 0.313,0.198 10 false SST
*a Turn
*b Hold


Place SST onto the front No. 2 axle outboard joint boot clamp LH.

SST
09521-24010  


iii.

Tighten SST so that the front No. 2 axle outboard joint boot clamp LH is pinched.

NOTICE:

Do not overtighten SST.



iv.
C106165
2.031,1.031 2.615,1.552 2.615,1.552 2.792,1.552 true 2.875,1.469 3.292,1.729 0.417,0.26 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp LH.

SST
09240-00020  (09242-00120, 09242-00300)

Standard Clearance:

1.2 to 4.0 mm (0.0473 to 0.1574 in.)


NOTICE:

If the measured value exceeds the specified value, retighten the front No. 2 axle outboard joint boot clamp LH.




b.

except TMMC Made:

i.
C107943

Install the front No. 2 axle outboard joint boot clamp LH onto the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly and install the front No. 2 axle outboard joint boot clamp LH as close to the inside of the vehicle as possible.

·

Check the band and lever for any deformation before folding back the lever.




ii.
C127684

Lean your weight on your hand and roll the front drive outboard joint shaft assembly LH forward while pressing the front drive outboard joint shaft assembly LH against a surface until a click sound is heard.

NOTICE:
·

Do not damage the deflector.

·

Make sure that the front drive outboard joint shaft assembly LH is in direct contact with the surface.




iii.
C127685

Using a plastic-faced hammer, tap the buckle to fix the lever in place while making sure that the end of the lever is even with the edge of the buckle.

NOTICE:

Do not damage the front axle outboard joint boot.




Hide 6.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 7.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

for TMMC Made:

i.

Install the front axle outboard joint boot clamp LH onto the outboard joint boot.


ii.
C106162
1.385,0.938 0.948,0.604 0.948,0.604 0.615,0.604 true 1.156,0.479 1.458,0.719 0.302,0.24 10 *b 1.875,1.938 2.271,2.146 0.396,0.208 10 *a 0.302,0.521 0.99,0.927 0.688,0.406 10 SST
*a Turn
*b Hold


Place SST onto the front axle outboard joint boot clamp LH.

SST
09521-24010  


iii.

Tighten SST so that the front axle outboard joint boot clamp LH is pinched.

NOTICE:

Do not overtighten SST.



iv.
C106163
1.25,1.469 0.948,1.698 0.948,1.698 0.771,1.698 false 0.385,1.604 0.865,1.875 0.479,0.271 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp LH.

SST
09240-00020  (09242-00120, 09242-00300)

Standard Clearance:

1.2 to 4.0 mm (0.0473 to 0.1574 in.)


NOTICE:

If the measured value exceeds the specified value, retighten the front axle outboard joint boot clamp LH.




b.

except TMMC Made:

i.
C129510

Install the front axle outboard joint boot clamp LH to the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before folding back the lever.




ii.
C129511

Using water pump pliers, pinch the front axle outboard joint boot clamp LH to temporarily fix it in place.


iii.
C129512

Using a plastic-faced hammer, tap the buckle to fix the lever in place while making sure that the end of the lever is even with the edge of the buckle.

NOTICE:

Do not damage the front axle outboard joint boot.




Hide 8.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 9.INSTALL FRONT DRIVE SHAFT DAMPER LH

a.

for TMMC Made:

i.
C268402
1.104,1.615 0.927,1.615 0.927,1.615 0.844,1.25 true 0.552,1.844 0.406,1.844 0.406,1.844 0.229,1.25 true 0.625,1.771 0.938,1.927 0.313,0.156 10 false *1 1.208,1.521 1.521,1.677 0.313,0.156 10 false *2 1.719,0.271 2.031,0.427 0.313,0.156 10 false (A)
*1 Front Drive Shaft Damper Clamp LH
*2 Front Drive Shaft Damper LH


Install a new front drive shaft damper clamp LH and front drive shaft damper LH onto the front drive outboard joint shaft assembly LH.

HINT:

Make sure the front drive shaft damper clamp LH is on the inboard joint side.



ii.

Adjust the position of the drive shaft damper LH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

153.0 to 157.0 mm (6.024 to 6.181 in.)




b.

except TMMC Made:

i.
C240143
0.74,1.406 0.865,1.917 0.865,1.917 0.99,1.917 true 1.521,1.771 1.375,1.771 1.375,1.771 1.229,1.302 true 1.625,0.229 1.844,0.406 0.219,0.177 10 (A) 1.052,1.833 1.292,2.01 0.24,0.177 10 *2 1.604,1.667 1.927,1.844 0.323,0.177 10 *1
*1 Front Drive Shaft Damper Clamp LH
*2 Front Drive Shaft Damper LH


Install a new front drive shaft damper clamp LH and front drive shaft damper LH onto the front drive outboard joint shaft assembly LH.

HINT:

Make sure the front drive shaft damper clamp LH is on the outboard joint side.



ii.

Adjust the position of the drive shaft damper LH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

158.0 to 162.0 mm (6.221 to 6.377 in.)




Hide 10.INSTALL FRONT DRIVE SHAFT DAMPER RH

a.

for TMMC Made:

i.
C268402
1.104,1.615 0.927,1.615 0.927,1.615 0.844,1.25 true 0.552,1.844 0.406,1.844 0.406,1.844 0.229,1.25 true 0.625,1.771 0.938,1.927 0.313,0.156 10 false *1 1.208,1.521 1.521,1.677 0.313,0.156 10 false *2 1.719,0.271 2.031,0.427 0.313,0.156 10 false (A)
*1 Front Drive Shaft Damper Clamp RH
*2 Front Drive Shaft Damper RH


Install a new front drive shaft damper clamp RH and front drive shaft damper RH onto the front drive outboard joint shaft assembly RH.

HINT:

Make sure the front drive shaft damper clamp RH is on the inboard joint side.



ii.

Adjust the position of the drive shaft damper RH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

161.0 to 165.0 mm (6.339 to 6.496 in.)




b.

except TMMC Made:

i.
C240143
0.74,1.406 0.865,1.917 0.865,1.917 0.99,1.917 true 1.521,1.771 1.375,1.771 1.375,1.771 1.229,1.302 true 1.625,0.229 1.844,0.406 0.219,0.177 10 (A) 1.052,1.833 1.292,2.01 0.24,0.177 10 *2 1.604,1.667 1.927,1.844 0.323,0.177 10 *1
*1 Front Drive Shaft Damper Clamp RH
*2 Front Drive Shaft Damper RH


Install a new front drive shaft damper clamp RH and front drive shaft damper RH onto the front drive outboard joint shaft assembly RH.

HINT:

Make sure the front drive shaft damper clamp RH is on the outboard joint side.



ii.

Adjust the position of the drive shaft damper RH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

161.0 to 165.0 mm (6.339 to 6.496 in.)




Hide 11.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH

a.
C127651
0.063,0.031 0.271,0.198 0.208,0.167 10 *A 0.073,2.292 0.302,2.469 0.229,0.177 10 *B
*A for One Touch Type
*B for Claw Engagement Type


Install the front drive shaft damper clamp LH.

NOTICE:

Be sure to install the front drive shaft damper clamp LH in the correct position.


i.

for One Touch Type:

Using a screwdriver, install the front drive shaft damper clamp LH as shown in the illustration.


ii.

for Claw Engagement Type:

Using needle-nose pliers, install the front drive shaft damper clamp LH as shown in the illustration.



Hide 12.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 13.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH

a.

Install new parts to the front drive outboard joint shaft assembly LH in the following order.

i.

Front axle inboard joint boot clamp LH


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp LH



b.

Remove the protective tape from the front drive outboard joint shaft assembly LH.


c.
C127694
1.927,1.188 2.083,1.833 2.083,1.833 1.365,1.531 true 2.083,1.833 2.25,1.833 false 2.313,1.729 3.042,1.896 0.729,0.167 10 *a
*a Matchmark


Align the matchmarks and place the beveled side of the tripod joint axial spline toward the front drive outboard joint shaft assembly LH.


d.

Using a brass bar and hammer, tap the tripod joint onto the front drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod in the correct direction.




e.
C127695

Using a snap ring expander, install a new snap ring.


f.

Pack the front drive inboard joint assembly LH and front axle inboard joint boot with grease from the boot kit.

Standard grease capacity:
for TMMC Made:

150 to 170 g (5.3 to 5.9 oz)

except TMMC Made:

175 to 185 g (6.2 to 6.5 oz)



g.
C127646
1.833,0.833 1.833,0.25 true 2.167,0.396 2.167,0.25 2.167,0.25 1.417,0.25 true 1.188,0.167 1.5,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly LH to the front drive outboard joint shaft assembly LH.


Hide 14.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C278922
0.094,0.083 0.406,0.281 0.313,0.198 10 *A 0.094,1.854 0.406,2.052 0.313,0.198 10 *B 1.531,1.573 1.844,1.771 0.313,0.198 10 (A) 1.594,3.104 1.906,3.302 0.313,0.198 10 (A)
*A for LH Side
*B for RH Side


Check that the 2 joint boots are not stretched or contracted when the front drive shaft is at the standard length.

Length (A):
Item Length
for TMMC Made LH Side 571.9 mm (1.88 ft.)
RH Side 918.0 mm (3.01 ft.)
except TMMC Made LH Side 577.6 mm (1.89 ft.)
RH Side 922.4 mm (3.03 ft.)


NOTICE:

Keep the drive shaft assembly level during inspection.


If the boots are stretched or contracted, correct them.


Hide 16.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127696
0.063,0.052 0.375,0.25 0.313,0.198 10 *A 0.104,2.208 0.365,2.375 0.26,0.167 10 *B
*A for One Touch Type
*B for Claw Engagement Type


a.

for One Touch Type:

Using a screwdriver, install the front axle inboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the boot.



b.

for Claw Engagement Type:

Using needle-nose pliers, install the front axle inboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the boot.



Hide 17.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 18.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front axle inboard joint boot clamp LH.


Hide 19.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.