Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Engine running
Combination switch assembly (ECO mode switch) off
Blower motor on
Temperature set to MAX HOT
IDH terminal signal below 1 V
(Inverter with converter assembly overload not detected)
·

Engine coolant temperature 65°C or less (2 heaters operate)

·

Engine coolant temperature 75°C or less (A heater operates)


Ambient temperature 10°C or less

WIRING DIAGRAM

E269936
5.958,0.594 6.573,0.792 0.615,0.198 10 false PTC1 5.708,0.479 5.896,0.656 0.188,0.177 10 false 40 4.531,1.677 4.719,1.854 0.188,0.177 10 false 1 3.24,0.958 3.427,1.135 0.188,0.177 10 false 5 3.24,0.49 3.427,0.667 0.188,0.177 10 false 2 4.531,0.958 4.719,1.135 0.188,0.177 10 false 3 2.01,0.729 2.854,0.927 0.844,0.198 10 false ECU-IG NO.3 0.219,0.563 1.563,0.76 1.344,0.198 10 false from IG1 NO.2 Relay 0.719,1.021 1.552,1.219 0.833,0.198 10 false from Battery 3.458,1.323 4.531,1.531 1.073,0.208 10 false PTC HTR NO.1 1.979,1.229 2.979,1.427 1,0.198 10 false PTC HTR NO.1 5.969,1.771 6.583,1.969 0.615,0.198 10 false PTC2 5.792,1.677 5.917,1.865 0.125,0.188 10 false 3 3.469,2.51 4.604,2.708 1.135,0.198 10 false PTC HTR NO.2 1.99,2.396 2.99,2.583 1,0.188 10 false PTC HTR NO.2 3.24,1.667 3.427,1.844 0.188,0.177 10 false 2 3.25,2.146 3.438,2.323 0.188,0.177 10 false 5 4.531,0.49 4.719,0.667 0.188,0.177 10 false 1 4.531,2.156 4.719,2.333 0.188,0.177 10 false 3 4.573,3.135 4.865,3.323 0.292,0.188 10 false A31 4.656,2.927 4.844,3.104 0.188,0.177 10 false 1 4.583,3.74 4.875,3.927 0.292,0.188 10 false A31 4.656,3.531 4.844,3.708 0.188,0.177 10 false 3 3.063,3.135 3.354,3.323 0.292,0.188 10 false A32 3.063,3.75 3.354,3.938 0.292,0.188 10 false A32 3.135,3.542 3.323,3.719 0.188,0.177 10 false 2 3.135,2.938 3.323,3.115 0.188,0.177 10 false 1 3.26,4.094 4.896,4.302 1.635,0.208 10 false Quick Heater Assembly 5.813,2.208 6.604,2.406 0.792,0.198 10 false G81 5.823,2.406 7.094,2.792 1.271,0.385 10 false Air Conditioning Amplifier Assembly 4.333,3.24 4.521,3.417 0.188,0.177 10 false B 4.354,3.833 4.542,4.01 0.188,0.177 10 false B 3.417,3.833 3.604,4.01 0.188,0.177 10 false E 3.406,3.24 3.594,3.417 0.188,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Heater Active Level Quick heater assembly Min.: 0, Max.: 3 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33

Result:
Proceed to
Heater Active Level changes normally
Heater Active Level does not change normally



Heater Active Level changes normally

2.INSPECT PTC HEATER RELAY

Heater Active Level does not change normally

2.INSPECT PTC HEATER RELAY
a.
E222294
1.115,0.938 1.219,0.479 1.219,0.479 1.354,0.479 false 1.063,1.344 1.229,1.75 1.229,1.75 1.365,1.75 false 0.563,1.281 0.729,1.75 0.729,1.75 0.885,1.75 false 0.792,0.979 0.688,0.5 0.688,0.5 0.531,0.5 false 1.385,0.396 1.604,0.656 0.219,0.26 10 1 1.385,1.667 1.604,1.927 0.219,0.26 10 2 0.906,1.667 1.125,1.927 0.219,0.26 10 3 0.448,0.406 0.667,0.667 0.219,0.26 10 5

Remove the PTC heater relays from No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)

NG

REPLACE PTC HEATER RELAY

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)
a.
E271244
0.042,0.042 0.354,0.24 0.313,0.198 10 *a 1.688,0.667 2,0.865 0.313,0.198 10 *2 1.271,1.281 1.583,1.479 0.313,0.198 10 *1
*1 PTC NO.1 Relay
*2 PTC NO.2 Relay
*a Component without relay installed
(No. 2 Engine Room Relay Block)


Remove the PTC heater relays from the No. 2 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC NO.1:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC NO.2:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Remove the PTC heater relays from the No. 2 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - G81-40 (PTC1) Always Below 1 Ω
1 - G81-3 (PTC2) Always Below 1 Ω
G81-40 (PTC1) - Body ground Always 10 kΩ or higher
G81-3 (PTC2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)
a.

Remove the PTC heater relays from the No. 2 engine room relay block.


b.

Disconnect the A31 quick heater assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC NO.1:
Tester Connection Condition Specified Condition
3 - A31-3 (B) Always Below 1 Ω
A31-1 (B) - Body ground Always 10 kΩ or higher

PTC NO.2:
Tester Connection Condition Specified Condition
3 - A31-1 (B) Always Below 1 Ω
A31-3 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)
a.

Disconnect the A32 quick heater assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-1 (E) - Body ground Always Below 1 Ω
A32-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT QUICK HEATER ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG