Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM30B0U _58 Vehicle Interior _009991 SEAT BELT _0054791 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B334890
0.854,0.406 1.688,0.406 true 0.823,1.927 1.74,1.927 true 0.625,1.844 0.938,2.042 0.313,0.198 10 false (1) 0.646,0.333 0.958,0.531 0.313,0.198 10 false (2)

Attach the guide to temporarily install the front shoulder belt anchor adjuster assembly and 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B334888

Align the 2 claws with the seat belt positioning holes, and install the retractor of the front seat outer belt assembly LH with the bolt as shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.
B334889

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



c.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for Front Passenger Seat Belt with Selectable Force Limiter)

a.
B339094

Align the 2 claws with the seat belt positioning holes, and install the retractor of the front seat outer belt assembly RH with the bolt as shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.
B339095

Connect the pretensioner connector and selectable force limiter connector, and lock the 2 locking buttons as shown in the illustration.

NOTICE:

Securely lock the locking button.



c.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 4.INSTALL CENTER PILLAR GARNISH LH

Hide 5.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

a.

Connect the floor anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Check that the front seat outer belt assembly LH is not twisted.


Hide 7.INSTALL OUTER LAP BELT ANCHOR COVER

a.

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 8.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 9.INSTALL REAR DOOR SCUFF PLATE LH

Hide 10.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 11.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION