Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM30B0U _58 Vehicle Interior _009873 INTERIOR PANELS / TRIM _0054291 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL REAR NO. 2 SIDE RAIL SPACER LH

a.

Attach the 2 clips to install the rear No. 2 side rail spacer LH.


b.

Attach the wire harness clamp.


c.

Connect the rear part of the curtain shield airbag assembly LH with a new clip.


d.
B337921
1.854,3.573 2.219,3.573 true 2.25,3.49 2.479,3.688 0.229,0.198 10 *1
*1 Pin


Push in the pin to lock the clip.


e.

Check that the curtain shield airbag assembly LH is not twisted.


Hide 2.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 3.INSTALL REAR SIDE RAIL SPACER LH

a.

Attach the clip to install the rear side rail spacer LH.


b.

Install the bolt.


c.

Hide 4.INSTALL REAR SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 5.INSTALL ROOF HEADLINING ASSEMBLY

a.

Place the roof headlining assembly into the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when placing it.


B337916


b.
B337915
1.167,2.542 1.479,2.74 0.313,0.198 10 *A 2.073,2.531 2.385,2.729 0.313,0.198 10 *A
*A w/o Sliding Roof


w/o Sliding Roof:

Install the roof headlining assembly with the 5 clips.


c.

w/ Sliding Roof:

Install the roof headlining assembly with the 3 clips.


d.

Attach the 3 wire harness clamps and 2 clips and connect the 2 connectors to the front pillar LH.


e.

Attach the 4 wire harness clamps to the front pillar RH.


f.

Connect the connector to the rear pillar RH.


g.

w/ Sliding Roof:

Connect the connector.


h.

w/ EC Mirror:

Connect the connector.


Hide 6.INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

B339885
2.5,1.677 2.5,1.26 2.5,1.26 2.677,1.26 true 2.5,1.823 2.5,2.01 2.5,2.01 2.677,2.01 true 2.708,1.177 3.021,1.375 0.313,0.198 10 *a 2.698,1.917 3.01,2.115 0.313,0.198 10 *b
*a Joint Portion of the Sun Roof Opening Trim Moulding
*b Cutout of the Roof Headlining Assembly


a.

Align the joint portion of the sun roof opening trim moulding with the cutout of the roof headlining assembly, and wedge the moulding onto the vehicle body and roof headlining to install it.


Hide 7.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

a.

Attach the 8 claws to install the inner rear view mirror cover.


Hide 8.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 9.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip assemblies.


a.

Install the 2 clips and 2 assist grip covers to the assist grip.


b.

Attach the 2 clips to install the assist grip assembly.


Hide 10.INSTALL MAP LIGHT ASSEMBLY

Hide 11.INSTALL VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B337902

Attach the 2 claws.


b.

Push in the visor holder to install it.


Hide 12.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 13.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FRONT PILLAR GARNISH LH

a.
B337794
0.552,0.823 0.896,0.823 false 2.354,0.417 2.49,0.208 2.49,0.208 2.698,0.208 false 0.396,0.76 0.615,0.958 0.219,0.198 10 *1 2.719,0.135 2.938,0.333 0.219,0.198 10 *2
*1 Protective Tape
*2 Front Pillar Garnish Clip


Attach the 3 guides.


b.

Turn the ends of the front pillar garnish clips 90° with needle-nose pliers and connect them to the front pillar garnish LH.

HINT:

Tape the tips of the needle-nose pliers before use.



c.
B337792
0.854,0.75 0.979,0.365 0.979,0.365 1.354,0.365 false 1.396,0.292 1.708,0.49 0.313,0.198 10 *1
*1 Front Pillar Garnish Clip


Attach the 2 front pillar garnish clips to install the front pillar garnish LH.


Hide 16.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 17.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the front seat outer belt floor anchor through the hole of the center pillar garnish LH.


b.

Attach the clip to install the center pillar garnish LH.


c.

Install the 2 clips.


Hide 18.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 19.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 2 claws and 2 clips to install the lower center pillar garnish LH.


b.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 20.INSTALL OUTER LAP BELT ANCHOR COVER

Hide 21.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 22.INSTALL SHOULDER BELT ANCHOR COVER RH

Hide 23.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH

a.

Attach the 8 clips to install the inner roof side garnish assembly LH.


b.

Connect the rear seat outer belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 24.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 25.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 26.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Connect the connector.


b.

Attach the 4 clips and 6 claws to install the deck trim side panel assembly LH.


c.

Install the luggage hold belt striker assembly with the bolt.


d.

Install the tether anchor set bracket with the bolt.


e.

Close the tether anchor set bracket cover.


f.

Connect the rear seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Install the 2 bolts and screw.

B337891


Hide 27.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

a.

Attach the 4 clips and 6 claws to install the deck trim side panel assembly RH.


b.

Install the luggage hold belt striker assembly with the bolt.


c.

Install the tether anchor set bracket with the bolt.


d.

Close the tether anchor set bracket cover.


e.

Connect the rear seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.

Install the 2 bolts and screw.

B337893


Hide 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B340039
1.75,0.24 2.031,0.24 2.031,0.24 2.281,0.583 false 1.896,3.219 1.896,3.083 1.896,3.083 1.74,3.021 true 1.604,0.167 1.917,0.365 0.313,0.198 10 *1 1.833,3.24 2,3.417 0.167,0.177 10 *2
*1 Paint Mark
*2 Mark Position


Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install the rear door opening trim weatherstrip LH as shown in the illustration.


Hide 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 30.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 6 clips and 2 claws to install the rear door scuff plate LH.


Hide 31.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 32.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B340040
1.896,0.323 2.156,0.323 2.156,0.323 2.281,0.573 false 1.479,3.094 1.688,3.094 1.688,3.094 1.708,2.792 true 1.74,0.25 2.052,0.448 0.313,0.198 10 *1 1.323,3.021 1.635,3.219 0.313,0.198 10 *2
*1 Paint Mark
*2 Mark Position


Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install the front door opening trim weatherstrip LH as shown in the illustration.


Hide 33.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 34.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Attach the 2 clips and 8 claws to install the front door scuff plate LH.


Hide 35.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 37.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

a.

Attach the 4 clips to install the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.


b.

Install the 4 screws.


c.

Close the No. 1 rear floor board.


Hide 38.INSTALL REAR FLOOR FINISH PLATE (for Compact Spare Tire)

a.

Attach the 2 guides, 4 clips and 2 claws to install the rear floor finish plate.


Hide 39.INSTALL REAR DECK TRIM COVER (for Full Size Spare Tire)

a.

Attach the 4 clips and 4 claws to install the rear deck trim cover.


Hide 40.INSTALL DECK FLOOR BOX LH

a.

Attach the 4 claws to install the deck floor box LH.


b.

Install the 3 clips.


Hide 41.INSTALL DECK BOARD ASSEMBLY

a.

Install the deck board assembly.


Hide 42.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.
B337882

Attach the 2 locks to install the tonneau cover assembly.


Hide 43.INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

a.
B337880

Attach the 4 locks to install the package tray trim pocket sub-assembly.


Hide 44.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION