Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2013.11
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E270419
2.646,0.771 2.865,0.927 0.219,0.156 10 false 12 2.635,1.406 2.854,1.563 0.219,0.156 10 false 9 2.156,0.75 2.583,0.948 0.427,0.198 10 false SNS2 2.167,1.417 2.604,1.604 0.438,0.188 10 false MCO- 0.917,2.042 1.354,2.229 0.438,0.188 10 false Q7 0.896,2.229 2.344,2.458 1.448,0.229 10 false Map Light Assembly 4.521,2.031 4.958,2.219 0.438,0.188 10 false G143 1.125,0.781 1.854,1.333 0.729,0.552 10 false Telephone Microphone Assembly 4.792,1.417 5.01,1.573 0.219,0.156 10 false 19 4.823,0.76 5.042,0.917 0.219,0.156 10 false 6 5.021,0.865 5.448,1.063 0.427,0.198 10 false SNS2 5.01,1.531 5.448,1.719 0.438,0.188 10 false MIN- 4.531,2.219 6.99,2.521 2.458,0.302 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [TELEPHONE MICROPHONE ASSEMBLY])
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q7 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-6 (SNS2) - Q7-12 (SNS2) Always Below 1 Ω
G143-19 (MIN-) - Q7-9 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly with its connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E237416
1.448,0.448 1.958,0.677 0.51,0.229 2.531,2.604 2.094,2.01 false 0.083,0.094 0.396,0.292 0.313,0.198 10 *a 1.51,0.479 1.927,0.667 0.417,0.188 10 G143 2.448,2.656 2.865,2.844 0.417,0.188 10 MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK MAP LIGHT ASSEMBLY

b.
E244514
1.792,1.552 2.052,1.927 true 1.313,1.563 0.854,1.677 true 0.448,1.604 1.063,1.802 0.615,0.198 10 SNS2 2.104,1.854 2.719,2.052 0.615,0.198 10 MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 9 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

DTCs are output