Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM
RM30B0U _51 Engine / Hybrid System _010069 CRUISE CONTROL _0054851 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA1  FCM Destination Information Unmatched  


DESCRIPTION

When the lane departure warning camera is replaced with a new one, it acquires the country specification information from the main body ECU (multiplex network body ECU). When the country specification information in the lane departure warning camera and main body ECU (multiplex network body ECU) do not match, DTC C1AA1 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA1 FCM Destination Information Unmatched While the initial check is running, the ignition switch is ON and the lane departure alert system is operating, country specification information in the lane departure warning camera and main body ECU (multiplex network body ECU) do not match for 1 second or more.
·

Lane departure warning camera

·

Main body ECU (multiplex network body ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the lane departure alert system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.ADJUST LANE DEPARTURE WARNING CAMERA
a.

Perform the lane departure warning camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Lane Departure Alert / Clear DTCs.


d.

Clear the DTCs.

Chassis > Lane Departure Alert > Clear DTCs
50002 355

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed between 50 km/h (32 mph) and 220 km/h (138 mph), and operate the lane departure alert system.



b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Chassis / Lane Departure Alert / Trouble Codes.


e.

Check for DTCs.

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Proceed to
No DTCs are output
DTC C1AA1 is output



No DTCs are output

END (LANE DEPARTURE WARNING CAMERA ADJUSTMENT IS DEFECTIVE)

DTC C1AA1 is output

4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.ADJUST LANE DEPARTURE WARNING CAMERA
5.ADJUST LANE DEPARTURE WARNING CAMERA
a.

Perform the lane departure warning camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Lane Departure Alert / Clear DTCs.


d.

Clear the DTCs.

Chassis > Lane Departure Alert > Clear DTCs
50002 355

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed between 50 km/h (32 mph) and 220 km/h (138 mph), and operate the lane departure alert system.



b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Chassis / Lane Departure Alert / Trouble Codes.


e.

Check for DTCs.

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Proceed to
No DTCs are output
DTC C1AA1 is output



No DTCs are output

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] IS DEFECTIVE)

DTC C1AA1 is output