Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM
RM30B0U _51 Engine / Hybrid System _010069 CRUISE CONTROL _0054851 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AAA  FCM Destination Information Uninitialized  


DESCRIPTION

When the lane departure warning camera is replaced with a new one, it acquires the country specification information from the main body ECU (multiplex network body ECU). If the lane departure warning camera cannot store the country specification information, DTC C1AAA is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAA FCM Destination Information Uninitialized While the ignition switch is ON, the lane departure warning camera cannot store the country specification information for 8 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera beam axis must be performed.

Click here

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the lane departure alert system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CLEAR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Lane Departure Alert / Clear DTCs.


d.

Clear the DTCs.

Chassis > Lane Departure Alert > Clear DTCs
50002 355

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.

HINT:

Wait for a minute or more with the ignition switch ON.



c.

Enter the following menus: Chassis / Lane Departure Alert / Trouble Codes.


d.

Check for DTCs.

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Proceed to
No DTCs are output
DTC C1AAA is output



No DTCs are output

DTC C1AAA is output

3.READ VALUE USING TECHSTREAM (DESTINATION INFORMATION)
3.READ VALUE USING TECHSTREAM (DESTINATION INFORMATION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / Lane Departure Alert / Data List.


e.

According to the display on the Techstream, read the Data List.

Chassis > Lane Departure Alert > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Destination Information Status of the country NOFIX, JPN, NA, EURO, AUS, GCC, SAFC, CHINA, CANADA, NZ, THAI, TWN or Read Error Actual country code -
Chassis > Lane Departure Alert > Data List
Tester Display
Destination Information
50003 355 6
OK:

Country specification information for lane departure warning camera and vehicle match.



Result:
Proceed to
OK
NG



OK

NG

4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.ADJUST LANE DEPARTURE WARNING CAMERA
5.ADJUST LANE DEPARTURE WARNING CAMERA
a.

Perform the lane departure warning camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

Result:
Proceed to
NEXT




NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Lane Departure Alert / Clear DTCs.


d.

Clear the DTCs.

Chassis > Lane Departure Alert > Clear DTCs
50002 355

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.

HINT:

Wait for a minute or more with the ignition switch ON.



c.

Enter the following menus: Chassis / Lane Departure Alert / Trouble Codes.


d.

Check for DTCs.

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Proceed to
No DTCs are output
DTC C1AAA is output



No DTCs are output

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] IS DEFECTIVE)

DTC C1AAA is output